Оценок - , средний балл:
(
)
)
Производитель: Homelite
Размер: 121.8 kb
Название файла: a7a9140e-925f-6354-596f-f02b64dd64ae.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
If a leak occurs, propane gas will sink to the lowest possible level. • Keep appliance area clear and free from combustible materials, gasoline, paint thinner, and other flammable vapors and liquids. Do not use heater in areas with high dust content. • Minimum heater clearances from combustibles: Outlet: 8 Ft. Sides: 2 Ft. Top: 6 Ft. Rear: 2 Ft. • Keep heater at least six feet from propane tank(s). Do not point heater at propane tank(s) within 20 feet. • Keep propane tank(s) below 100° F. • Check heater for damage before each use. Do not use a damaged heater. • Check hose before each use of heater. If highly worn or cut, replace before using heater. • Locate heater on stable and level surface if heater is hot or operating. • Not intended for use on finished floors. • Never block air inlet (rear) or air outlet (front) of heater. • Keep heater away from strong drafts, water spray, rain, or dripping water. • Do not leave heater unattended. • Keep children and animals away from heater. • Never move, handle, or service a hot, operating, or plugged-in heater. Severe burns may result. Wait 20 minutes after turning heater off. • To prevent injury, wear gloves when handling heater. • Never attach duct work to heater. • Do not alter heater. Keep heater in its original state. • Do not use heater if altered. • Turn off propane supply and unplug heater when not in use. • Use only original replacement parts. This heater must use design-specific parts. Do not substitute or use generic parts. Improper replacement parts could cause serious or fatal injuries. Generic LP 155 LP-PFA/PV 008B Outlet (Front) Handle Upper Shell On/Off Switch Power Cord Hose /Regulator Assembly Inlet Connector Lower Shell Fan Guard Outlet (Front) Handle Upper Shell On/Off Switch Power Cord Hose /Regulator Assembly Inlet Connector Lower Shell Fan Guard Hot Air PRODUCT IDENTIFICATION Figure 1 - HP155A 1. Remove all packing items applied to heater for shipment. Keep plastic cover UNPACKING caps (attached to inlet connector and hose/regulator assembly) for storage. 2. Remove all items from carton. 3. Check all items for shipping damage. If heater is damaged, promptly inform dealer where you bought heater. 4 The Fuel System: The hose/regulator assembly attaches to the propane gas THEORY OF supply. The propane gas moves through the solenoid valve and out the nozzle. OPERATION The Air System: The motor turns the fan. The fan pushes air into and around the combustion chamber. This air is heated and provides a stream of clean, hot air. The Ignition System: The direct spark ignitor (DSI) sends voltage to the ignitor. The ignitor ignites the fuel and air mixture. The Safety Control System: This system causes the heater to shut down if the flame goes out. Combustion Chamber Fan Clean Heated Air Out (Front) Cool Air In (Back) Solenoid ValveDSI Nozzle On/Off Switch Power Cord Ignitor Motor Hose/Regulator Assembly Air For Combustion Fuel And Heating Figure 2 - Cross Section Operational View 5 Propane gas and propane tank(s) are to be furnished by the user. PROPANE Use this heater only with a propane vapor withdrawal supply system. See Chapter SUPPLY 5 of the Standard for Storage and Handling of Liquefied Petroleum Gas, ANSI/ NFPA 58 and/or CAN/CGA B149.2. Your local library or fire department will have this booklet. The amount of propane gas ready for use from propane tanks varies. Two factors decide this amount: 1. The amount of propane gas in tank(s) 2. The temperature of tank(s) The chart below shows the number of 100 pound tanks needed to run this heater. Do not operate this product with any tank smaller than 100 pounds. Temperature (°F) At Tank 32° 20° 10° 0° -10° -20° Number of tanks 2 2 3 3 (Use larger tank) Less gas is vaporized at lower temperatures. You may need two or more 100 pound tanks or one larger tank in colder weather. Your local propane gas dealer will help you select the proper supply system. The minimum surrounding-air temperature rating for this heater is -20°F (-29°C). INSTALLATION ! WARNING Review and understand the warnings in the Safety Information Section, pages 2 and 3. They are needed to safely operate this heater. Follow all local codes when using this heater. ! WARNING Test all gas piping and connections for leaks after installing or servicing. Never use an open flame to check for a leak. Apply a mixture of liquid soap and water to all joints. Bubbles forming show a leak. Correct all leaks at once. 1. Provide propane supply system (see Propane Supply above). 2. Connect POL fitting on hose/regulator assembly to propane tank(s). Turn POL fitting counterclockwise into threads on tank. Tighten firmly using wrench. IMPORTANT:Tighten regulator with vent pointing down. Pointing vent down protects regulator from weather damage. Figure 3 - Regulator With Vent Pointing Down Continued Hose Regulator Vent (pointing down) POL Fitting Supply Valve Propane Tank 3. Connect hose to inlet connector. Tighten firmly using a wrench. IMPORTANT:Extra hose...
Эта инструкция также подходит к моделям:Электрообогреватели - UT65052-A (121.8 kb)