Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Turn the heater on by switching the Power ON/OFF switch located on the back panel of the heater, to the ‘ON’ position. An audible beep will sound. The heater is now in standby mode. Using The Remote Control Your heater may be operated using either the control panel or the remote control. The remote control uses 2 x AAA batteries. To access the battery compartment, simply remove the cover at the rear of the remote control. To operate, ensure that you point KCE640_IB_FA.indd 8 16/10/09 10:50 AM Use the MODE button to select the desired heat setting. The MODE button allows you to select from two heat settings. HIGH – High heat setting (2000 watts) LOW – Low heat setting (1200 watts) Turn the heater off by switching the Power ON/OFF switch located at the back panel of the heater, to the ‘OFF’ position. NOTE: This heater features a tip-over switch. If the heater tips over, it will automatically switch off. Once placed back into the upright position, the heater will be in standby mode, and the settings will need to be selected again. Before First Use Remove any promotional material or packaging from the heater. Unwind the cord to its full length and place the heater on a firm, level surface in a stable upright position. Visually inspect the air inlet and outlets to ensure there are no blockages. When unpacking the heater, check to see you have received the remote control, before discarding the packaging. Turning Your Heater On Plug the cord into a 230V or 240V power point and switch on. NOTE: To avoid an electrical circuit overload, it is recommended that no other appliances are plugged into the same circuit as your heater, when it is in use. Turn the heater on by switching the Power ON/OFF switch located on the back panel of the heater, to the ‘ON’ position. An audible beep will sound. The heater is now in standby mode. Using The Remote Control Your heater may be operated using either the control panel or the remote control. The remote control uses 2 x AAA batteries. To access the battery compartment, simply remove the cover at the rear of the remote control. To operate, ensure that you point KCE640_IB_FA.indd 8 16/10/09 10:50 AM 9 Setting the Oscillation The oscillation function works at both operating temperatures. Press the SWING button once to activate. The heater will begin to oscillate from side to side. Press the SWING button again to stop the heater from oscillating. Setting the Auto-Off Timer The timer function works at both operating temperatures, and switches the unit off after a preset number of hours. Press the TIMER button to activate the timer settings. The 30 minute LED will illuminate. Press the TIMER button to cycle through the 30 minute and one hour increments, up to 7.5 hours. The heater will then switch itself to standby mode after the selected number of hours has passed. ThermoGuard Overheating Safety Device Your heater is fitted with a safety device that switches off the heater in the event of overheating. Should this heater stop working, turn off the heater and inspect the air inlet and outlet for blockages. Wait for at least five minutes for the protection system to reset before attempting to restart the heater. If the heater fails to operate or the safety device switches off again, return the heater to your nearest service centre for examination or repair. KCE640_IB_FA.indd 9 16/10/09 10:50 AM Press the TIMER button to cycle through the 30 minute and one hour increments, up to 7.5 hours. The heater will then switch itself to standby mode after the selected number of hours has passed. ThermoGuard Overheating Safety Device Your heater is fitted with a safety device that switches off the heater in the event of overheating. Should this heater stop working, turn off the heater and inspect the air inlet and outlet for blockages. Wait for at least five minutes for the protection system to reset before attempting to restart the heater. If the heater fails to operate or the safety device switches off again, return the heater to your nearest service centre for examination or repair. KCE640_IB_FA.indd 9 16/10/09 10:50 AM 10 Ensure that the heater is switched off and disconnected from the power point before cleaning. Use a clean, dry cloth to clean the external surfaces of the heater. If the heater has collected dust or dirt inside the unit or around the elements, have the unit cleaned by a qualified service agent. Do not operate the heater in this condition. Do not attempt to open the case of the heater at any time as there are no customer serviceable parts inside. When not in use, store the heater (preferably in its original box) in a cool, clean and dry location. The air filter at the rear of the heater can be easily cleaned by removing the filter casing panel and removing the mesh filter. A basic clean in warm water to remove any build up is adequate and allow time to completely dry before replacing the filter and the filter casing panel. Care and Cleaning KCE640_IB_FA.indd 10 16/10/09 10:50 AM...