Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Installation on Rugs and Tile If this appliance is to be installed directly on carpeting, tile, or other combustible material, other than wood flooring, the appliance shall be installed on a metal or wood panel extending the full width and depth of the appliance. The base referred to above does not mean the fire-proof base as used on wood stoves. The protection is primarily for rugs that may be extremely thick and light-color tile that can discolor. Figure 3 Figure 2 Figure 4 Page 8 16938-3-0806 APPLIANCE HARDWARE PACKAGE Appliance Hardware Package Parts List Part Description Part Number Quantity Supplied 1/4-20 x 1" Phillips Head Bolt R-3188 4 1/4-20 x 3/8" Phillips Head Bolt R-3646 16 1/4-20 x 1/2" Leveling Bolt R-3747 4 No. 10 x 1/2" Hex Washer Head Screw R-2737 10 1/4-20 Washer Head Nut R-3185 4 Leg Pad "A" (see Figure 6) CI-008 2 Leg Pad "B" (see Figure 6) CI-009 2 1-1/4" x 1/2" Retaining Tab (see Figure 8) CI-007 4 1/4" x 9/32 Washer (Not Shown) R-1150 8 Figure 5 16938-3-0806 Page 9 ASSEMBLY OF STOVE CASTING Assembly of Stove Casting (Figures 6, 7, 8, 9, 10, 11 and 12) Attention: Included in the hardware package are (8) 1/4" inside diameter washers. A 1/4" washer may be used with a 1/4-20 x 3/8" bolt when assembling the stove casting parts. If a bolt hole is not tapped deep enough for a tight fit between stove casting parts, the 1/4" washer can be used as a shim to provide a tight fit. The 1/4" washers are not required for assembly of the stove casting if all the bolt holes are tapped to a proper depth. Additonal 1/4" washers are to be purchased locally. 1. Place porcelain casting pieces on a non-abrasive surface in order to protect the porcelain finish. The exterior of the porcelain casting pieces should be facing the non-abrasive surface. 2. The assembly of the casting is accomplished in 7 stages: A. Attaching legs to the sides (Figure 6). B. Attaching rear cover to sides (Figure 7). C. Removing protective packaging from casting front and window (Figure 8). D. Assembly of front by attaching retaining tabs and placing front on unit (Figure 8 and Figure 9). E. Inserting firebox into partially completed assembly (Figure 10 and Figure 11). F. Attaching firebox to rear cover (Figure 12). G. Placing top on unit. Detailed Instructions Follow 3. Refer to Figure 6, the leg pads will have the letter "A" and "B" stamped into the metal. Place leg pad "A" and leg pad "B" at the bottom of each casting side. Leg pad "A" attaches to the front of the casting side, right and to the rear of the casting side, left. Leg pad "B" attaches to the rear of the casting side, right and to the front of the casting side, left. Position the 3/4" flange on the leg pad against the (2) locator dimples on the casting side. The 3/4" flange must be facing upward, toward the top louver openings on the casting side. Attach the two rear leg pads to the casting sides with (2) 3/8" bolts. Attach but do not completely tighten the two front leg pads to the casting sides with (2) 3/8" bolts. Attention: The front leg pads can be adjusted to provide a snug fit between the casting front and the casting sides. 4. Attach (4) leveling bolts to the bottom of the (4) legs. 5. Align the 3/8" hole at the top of the leg with the 3/8" hole in the leg pad. Attention: For proper positioning of the leg to the leg pad the (2) 1-1/2" top edges of the leg must be placed flush and parallel to the (2) edges on the leg pad. Attach leg to leg pad by inserting (1) 1" bolt through the leg pad and into the leg, secure bolt with 1/4" nut. 6. Insert (2) 3/8" bolts into the (2) holes on the edges of the casting sides. The bolts should only be threaded half-way into the holes in order to allow for clearance when the casting back is attached to the casting sides. Figure 6 Page 10 16938-3-0806 7. Refer to Figure 7, the rear cover has (4) keyholes for attachment to the casting sides. Stand the casting sides on the floor with the (2) bolts attached half-way into the edges of the rear cover positioned at the rear. The large diameter holes in the keyholes of the rear cover will be toward the floor. Working with one casting side at a time, place the large diameter holes in the keyholes over and behind both of the bolts at the same time. Push downward on the rear cover to lock the keyholes into position behind the bolts. Finish tightening both bolts to secure rear cover to casting side. Repeat this procedure to secure rear cover to the second casting side. Figure 7 8. Position the completed portion of the casting in the approximate location for installation as the completed assembly will be heavy. 9. Refer to Figure 8, remove protective packing foam from casting front and window. Remove the (1) 3/4" bolt and (1) 1/4" washer from top of window. Remove (1) 3/8" bolt and 1 - 5/8" x 3/4" retaining tab from bottom of window. Remove the window from casting front. Remove the protective sheet of foam from the casting front. Place the window into the casting front. Attach the top of the w...
Эта инструкция также подходит к моделям:Электрообогреватели - CIVF-25-21 (1.73 mb)