Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Please read this manual before attempting to move or install your unit. We wish you many years of safe heating pleasure with your new heating appliance. CAUTION: This unit must be installed in accordance with these instructions and must comply with local building and fire codes. Failure to do so could result in a chimney or house fire. Keep children, furniture, fixtures, and all combustible materials away from any heating appliance. Maintain a minimum clearance of 30 inches (6 inches if using a heat shield) from the firebox and 18 inches from the flue pipe to any combustibles, unless you are using shielded or double wall pipe. Visit our web site at for helpful information, frequently asked questions, parts & accessory orders and more. DO NOT INSTALL THIS UNIT IN A MOBILE HOME!!! READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLING THIS MODEL. SAVE THIS MANUAL FOR FUTURE REFERENCE. NOTE: IF YOU HAVE A PROBLEM WITH THIS UNIT DO NOT RETURN IT TO THE DEALER. CONTACT CUSTOMER SERVICE @ 1-800-245-6489. MODEL 24-G FURNACE SAFETY NOTICE IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE FIRE MAY RESULT. FOR YOUR SAFETY, FOLLOW THE INSTALLATION DIRECTIONS. CONTACT YOUR LOCAL BUILDING OR FIRE OFFICIALS CONCERNING RESTRICTIONS AND INSTALLATION INSPECTIONS IN YOUR AREA. Text Box: Rev. 1/06 Text Box: England’s Stove Works highly recommends the use of smoke detectors and Carbon Monoxide detectors with any hearth product, including this unit. Follow all manufacturer’s instructions when using smoke or Carbon Monoxide detectors. SECTION I: FLUE SYSTEM A. Existing Flue System If you have chosen a freestanding unit, this stove is designed to connect to an existing flue system, such as masonry or a pre-manufactured Class A flue system. If you have a masonry flue system, the inner liner should be inspected carefully for cracks; if there is no liner in your chimney, we recommend you install a steel liner or have one installed. If you have an existing pre-manufactured system the inner liner should be inspected for warping or buckling. Either type chimney system should be thoroughly cleaned before installing your new stove. We strongly recommend you have a qualified chimney sweep clean and inspect your entire system, as the sweep can spot problems you might overlook. The sweep in most cases can make any necessary repairs or recommend a qualified person to do so. It is not permissible to connect this unit to a chimney that is servicing another unit. B. Flue Size The proper flue size is determined by measuring the inside diameter of the flue collar on the unit. This stove is equipped with a six inch (6”) TOP EXHAUST FLUE COLLAR. Therefore, the connector pipe should be six inches (6”) and never less in diameter than the collar on the stove. The area of the chimney liner must also be equal to or greater than the area of the flue collar on the stove. If the area of the flue is greater than the collar, it should never be more than three (3) times greater. Example: The area of a six inch (6”) diameter flue collar is 28.87 square inches, therefore the connector pipe should be at least six inches (6”) in diameter but no greater than 84.8 square inches. The black connector pipe should be 24 gauge steel and eighteen inches (18”) from a combustible wall or ceiling. This clearance can be reduced to six inches (6”) if you are using a double wall or shielded pipe. C. Installation of a New Flue System 1. Masonry Flue: In the event that you plan to install or have a system installed, there are several approaches that you can take. In the middle and late seventies masonry flue systems became very popular, and today this type system is satisfactory. If you are considering a masonry system, you should consult with your local building officials for the proper procedures on this type chimney. We recommend you consult with and have your flue built by a licensed, bonded contractor. Most masonry chimney systems are placed against an outside wall and extend upward beside the house. The flue thimble is then inserted through the wall, making the connection with the stovepipe and the vertical flue. Exercise extreme caution when drilling through the wall -- you must maintain proper clearance between the connecting liner and any combustible material in the wall. We also recommend you have a flue clean-out door located at least two feet (2’) below your thimble for easy cleaning of the system. This door should be made as airtight as possible. It is the consumer’s responsibility to ensure the chimney system is safe and in good operating condition. The manufacturer will not be held responsible for an accident attributed to a unit connected to a faulty chimney system. 2. Pre-Manufactured Flue System: In the past few years pre-manufactured flue systems have become very popular, because this type system is easily installed and, when done correctly, is very safe. There are many pre-manufactured flue systems on the market, and when making your ch...