Оценок - 5, средний балл: 3.4
(
)
)
|
Фрагмент инструкции
It cuts off the power as soon as the heater’s internal temperature becomes too high. This patented, technologically advanced system requires the user to reset the heater in case of a potential overheat situation. It will only resume operation when the user resets it. To Reset the Heater: 1. Unplug the heater and wait 10 minutes for the unit to cool down. 2. After the 10 minutes, plug the unit in and operate normally. PRE-OPERATING INSTRUCTIONS Carefully unpack your heater from the box (it is recommended to save the box for off-season storage). OPERATING INSTRUCTIONS 1. Place the unit on a firm level surface. Plug in the heater to a 120V power source. 2. To start the unit, press the Power button (BCH3220) or turn the mode knob (BCH3210) located on the control panel. The power light will remain lit while the heater is in operation. For BCH3210, make sure that the mode knob is in the OFF position. THERMOSTAT INSTRUCTIONS On the first use, the heater will operate in fan mode. After initial use, the heater will operate on the last programmed setting. This function allows you to set the heater to your desired comfort level. The heater will maintain your desired room temperature. For BCH3210: 1. Set the THERMOSTAT knob to the highest setting, clockwise as far as it will turn. 2. When the desired room temperature level is reached, lower the thermostat setting, by turning the THERMOSTAT knob counter clockwise as far as it will turn. 3. The thermostat will now automatically maintain the pre-set temperature level by turning the heater on and off. The thermostat is now set. Figure 1 High Current Room Temperature Indicator Set Temperature ff Higher Power Lower Button Set Mode Temperature Night Light Button Indicator Button BCH3220 BCH3210 For BCH3220: 1. To change the heater settings, press the MODE button. Each time you press the MODE button, it will scroll through the settings FAN, LOW, HIGH, AUTO. Note: The fan speed will not change when the mode is changed from low to high. 2. Select the AUTO mode. 3. Set the heater to the desired room temperature by pressing the (+) or (-) buttons. Note that the degree range is from 60°F - 85°F (15°C - 29°C). If you scroll past 85°F (29°C) the display will automatically loop to 60°F (15°C). 4. Now the desired temperature is set. Note: When the temperature in the proximity of the heater reaches the set temperature, the heater will automatically turn on. The fan will continue to run cooling the heater for 30 seconds. The unit will operate again when the temperature falls below the preset temperature. mode thermostat Fan Low Mode HIGH LOW FAN AUTO ROOM TEMP. SET TEMP. Light Sensor . TIP: It is normal for the heater to cycle ON and OFF as it maintains the preset temperature. To prevent the unit from cycling, raise the thermostat setting. 90° SWIVEL INSTRUCTIONS For maximum heat distribution use the revolutionary vertical twin housing configuration to allow heat to travel in two different directions. 1. Carefully adjust each swivel to direct the heat flow. 2. Do not swivel the unit beyond the point of resistance. NIGHTLIGHT (BCH3220 only) 1. The nightlight will automatically light when the room becomes dark. When the room becomes light, the nightlight will automatically turn off. 2. To turn the nightlight off, press the button on the control panel. . TIP: The nightlight will not automatically operate until the button is pressed again. MAINTENANCE INSTRUCTIONS During Season Care 1. Before cleaning make sure the unit is unplugged. Allow the heater to cool before cleaning. 2. Carefully wipe the unit with a soft, damp cloth. Please be cautious near the heating elements. . TIP: Over time, dust may accumulate on the front grills. This can be removed by wiping the unit with a damp cloth. Always unplug unit and allow to cool prior to cleaning. After Season Care Store heater in a cool, dry location. Bionaire® recommends storing the unit in its original, or appropriately sized, box. HEATER SERVICE INSTRUCTIONS 1. Do NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void the warranty. The inside of the unit contains no user serviceable parts. All servicing should be performed by qualified personnel only. 2. If you need to exchange the unit, please return it in its original carton, with a sales receipt, to the store where you purchased it. If you are returning the unit more than 30 days after the date of purchase, please see the enclosed warranty. 3. Should your heater require service, please call 1-800-788-5350 in North America for further assistance. 4. . If you have any other questions or comments, feel free to write to us: PO Box 400 Milford, MA 01757 USA Canada 6385 Shawson Drive Mississaugua, Ontario Canada, L5T IS7 Visit our website at WARRANTY Bionaire® warrants to the first retail purchaser, for TWO (2) YEARS from the date of original purchase, either to repair or replace at its option, without charge (parts and labor), any ...
Эта инструкция также подходит к моделям:Электрообогреватели - BCH3220 (6.57 mb)