Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
After 30 seconds, release control knob. Now follow steps 9 through 11, Lighting Instructions, column 1. OPTIONAL REMOTE OPERATION Note:All remote control accessories must be purchased separately (see Accessories, page 24). Follow instructions included with the remote control. Thermostat Control Operation (Optional GHRCTA Series Only) The thermostat control setting on the remote control unit can be set to any comfort level between WARMER and COOLER. The burners will turn on and off automatically to maintain the comfort level you select. The ideal comfort setting will vary by household depending upon the amount of space to be heated, the output of the central heating system, etc. For wall thermostat operation, follow instruction supplied with thermostat accessory GWMT1. For wall switch operation follow instructions supplied with GWMS2. NOTICE: You must light the pilot before using the remote control unit. SeeLighting Instructionson pages 14 and 15. 1. After lighting, let pilot flame burn for about one minute. Turn control knob to ON position. Adjust flame adjustment knob anywhere between HI and LO. Slide the selector switch to the AUTO position. Note: The burners may light if hand-held remote ON button was on when selector switch was last turned off. You can now turn the burners on and off with the handheld remote control unit. IMPORTANT: Do not leave the selector switch in the AUTO position when the pilot is not lit. This will drain the battery. IMPORTANT: Be sure to press the ON/OFF buttons on the hand-held remote control unit for up to 3 seconds to assure proper operation. GHRC Series Operation: 2a. Press the ON/OFF button to turn the burners on and off. When turning burners off, the pilot will remain lit. GHRCTA Series Operation: 2b. Press the AUTO/ON/OFF button on the hand-held remote control (see Figure 24, page 16). The lights to the left of the button will show AUTO, ON, or OFF. • In the ON mode, the burners will ignite. The heater is in manual mode when ON is lit. • In the AUTO mode, the thermostat in the hand-held remote unit controls the room temperature. To increase the room temperature, press the top arrow of the TEMP button. To lower the room temperature, press the bottom arrow of the TEMP button. At higher settings the heater will run longer. Continued CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve. WARNING: Make sure the selector switch is in the OFF position when you are away from home for long periods of time. Heater will come on automatically with selector switch in the ON position. 15 FIREPLACE MANUFACTURERS INC. UNVENTED NATURAL GAS LOG HEATER OPERATING HEATER Continued IMPORTANT: This remote control has been specially engineered to take an air temperature sample every 5.5 minutes in the auto mode. It will not respond immediately to the temperature setting being turned up or down. IMPORTANT: The hand-held remote control unit must be near the heater. Do not keep the hand-held remote control unit too close to the heater. The thermostat on the hand-held remote control unit will heat up too quickly and turn the heater off. 3. To turn the burner off, press the AUTO/ON/OFF button until OFF lights. The pilot will remain lit. IMPORTANT: To turn the pilot off, manually turn the control knob on the heater to the OFF position. Control Knob in INSPECTING BURNERS Check pilot flame pattern and burner flame patterns often. PILOT FLAME PATTERN Figure 25 shows a correct pilot flame pat- tern. Figure 26 shows an incorrect pilot flame pattern. The incorrect pilot flame is not touching the thermocouple. This will cause the thermocouple to cool. When the thermocouple cools, the heater will shut down. If pilot flame pattern is incorrect, as shown in Figure 26 • turn heater off (see To Turn Off Gas to Appliance, page 15) • see Troubleshooting, pages 18 through 20 OFF P ILOT ON LO IHON OFF REMO TE Selector Switch in Remote Position On Position Flame Adjustment Knob Figure 23 - Setting the Remote Selector Switch, Control Knob, and Flame Adjustment Knob for Remote Operation Shows Temperature Setting The Log Heater will Automatically Cycle between Pilot and the Heat Setting that has been Selected Increases Room Temperature in AUTO Mode Decreases Room Temperature in AUTO Mode Turns Burners On or Off and Allows You to Choose the Auto Setting Pilot Burner Thermocouple ThermocouplePilot Burner Figure 25 - Correct Pilot Flame Pattern Figure 26 - Incorrect Pilot Flame Pattern Figure 24 - Thermostat Hand-Held Remote Control Unit Selections (GHRCTA Series Only) 105072 16 OWNER’S MANUAL INSPECTING BURNERS Continued FRONT BURNER FLAME PATTERN Figure 27 shows correct front burner flame pattern. Figure 28 shows incorrect front burner flame pattern. The incorrect burner flame pattern shows yellow tipping at top of blue flame. WARNING: If yellow tipping occurs, your heater could produce increased levels of carbon monoxide. If front burner flame pattern shows yellow tipping, follow instructions ...
Эта инструкция также подходит к моделям:Электрообогреватели - VFN18R (497.92 kb)
Электрообогреватели - VFN24R (497.92 kb)