Оценок - 2, средний балл: 4 ( )

Производитель: Louisville Tin and Stove Размер: 291.64 kb Название файла: Язык инструкции:

Allow for elevation derating when sizing gas heating equipment. NATURAL GAS SPECIFIC ELEVATIONS Model 0 to 2,000-4,000 -6,000 -8,000’ No. 2,000’ 4,000’ 6,000’ 8,000’ 10,000’ VC201 45 47 48 49 VC351 35 37 38 40 VC501 30 31 31 32 VC701 25 27 28 29 VCR351 35 37 38 40 VCR501 30 31 31 32 VCR701 25 27 28 29 50 42 35 30 42 35 30 ORDER KIT #49820 45-1 HIGH ALTITUDE KIT L.P. GAS SPECIFIC ELEVATIONS Model 0 to 2,0004,000 6,000 -8,000’ No. 2,000’ 4,000’ 6,000’ 8,000’ 10,000’ VC202 1.3mm 55 56 56 57 VC352 1.65mm 53 53 54 54 VC502 47 49 49 50 51 VC702 41 42 43 44 46 VCR352 1.65mm 53 53 54 54 VCR502 47 49 49 50 51 VCR702 41 42 43 44 46 ORDER KIT #49820 45-1 HIGH ALTITUDE KIT STEP 6. Install glass panels by inserting top edge into upper retainer and lower into bottom support, and slide glass into position. Do not allow a crack between the two glass panels. Never operate heater with either glass missing or cracked. STEP 7. Re-install bezel by placing bezel tabs over lower front and swing bezel into position and secure with three screws. Page 8 THIS IS A GAS-FIRED APPLIANCE, KEEP THE AREA CLEAR OF GASOLINE AND OTHER FLAMMABLE VAPORS AND LIQUIDS. ALL COMBUSTIBLE MATERIAL MUST BE KEPT CLEAR OF THIS AREA. HAVE A QUALIFIED SERVICEMAN CHECK THE BURNER PERIODICALLY. REMOVE AND CLEAN IF NECESSARY. CAUTION: There may be momentary and spasmodic orange flashes in the flame. This is caused by the burning of air borne dust particles and is not to be confused with the yellow tipping which is a stable or permanent situation when there is insufficient primary air. PROPER BURNER FLAME 3” TO 5” 1/4” INNER MANTLE 1/4” OUTER MANTLE 3 - 5” FIGURE 3 SERVICE RECORD MAINTENANCE CLEANING: To clean the front casing of your heater, it is only necessary to use a soft cloth. Light dust can be removed in this way. To obtain a polish or gloss, use a little light machine oil on the cloth. Do not use metal polish or cleaning solution. The burner ports should be kept free from lint and dust. CLEANING OF COMBUSTION CHAMBER The combustion chamber of your console heater should never need to be cleaned if proper burner adjustment and gas pressures are maintained. However, if an unusual circumstance should occur, the following procedure should be followed in cleaning your combustion chamber. 1. Turn off gas supply to heater at manual valve in supply line to heater. 2. Disconnect heater at ground joint union ahead of main gas valve. 3. Remove main control and orifice assembly. 4. Remove burner. 5. Remove combustion chamber. 6. Using a scraper, scrape inside of a primary combustion chamber. This should be area of heaviest accumulation of carbon. 7. Remove plug bottom located in bottom rear of second combustion chamber. Using a bottlebrush, clean inside of this chamber. Shake residue out the clean-out hole. 8. Clean the rear chamber by using bottlebrush through the vent tube openings. 9. Replace combustion chamber, burner and control. Check all gas piping for leaks before lighting heater. Repair service should be performed by qualified persons. The heater should be inspected before initial use. An annual cleaning of control compartment and safety performance check should be made by a qualified service person. More frequent cleaning may be required when exposed to the excessive lint conditions due to carpeting and bedding material, etc. It is imperative that the control compartment, burners, and circulating air passageways of the heater be kept clean. Any safety screen, casing top, or guard removed for servicing the heater must be replaced prior to operati...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: