Оценок - , средний балл: ( )

Инструкция по эксплуатации Cadet, модель DV35IN33L

Производитель: Cadet
Размер: 2.79 mb
Название файла:

Язык инструкции:

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

• Improper positioning of the logs or glass door assembly. • Installation and/or use of any component part not manufactured or approved by manufacturer. The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code ANSI Z223.1/NFPA 54* Natural Gas and Propane Installation Code, or CSA B149.1 in Canada. *Available from the American National Standards Institute, Inc. 11 West 42nd St., New York, N.Y. 10036. 23015-3-0707 Page 5 DV25IN33L MODELS LP Input Btu/hr Maximum 25,000 Btu/hr Minimum 17,000 KWH (Maximum) 7.30 (Minimum) 5.00 Orifice #53 (0.0596) Air Shutter Opening Full Open DV33IN33L MODELS LP Input Btu/hr Maximum 33,000 Btu/hr Minimum 25,000 KWH (Maximum) 9.57 (Minimum) 7.30 Orifice #51 (0.067) Air Shutter Opening Full Open DV35IN33L MODELS LP Input Btu/hr Maximum 35,000 Minimum 27,000 KWH (Maximum) 10.15 (Minimum) 7.83 Orifice #50 (0.070) Air Shutter Opening Full Open SPECIFICATIONS Nat 25,00017,000 7.305.00 #42 (0.0935) 1/8” Nat 33,00025,000 9.576.67 #34 (0.111) 3/16” Nat 35,00025,000 10.157.30 #33 (0.113) 3/16” Remote Control Accessories Description FRBC Millivolt Battery Remote ON/OFF FRBTC Millivolt Battery Remote T-Stat TMV Millivolt WIRELESS Wall Thermostat TRW Millivolt Reed Switch Wall Thermostat Surround Kits Description Contemporary S256BL 6” Wide, black for use on DV25IN models S336BL 6” Wide, black for use on DV33IN models S356BL 6” Wide, black for use on DV35IN models Traditional Cast Iron SC256BL 6” Wide, black for use on DV25IN models SC336BL 6” Wide, black for use on DV33IN models SC356BL 6” Wide, black for use on DV35IN models Venting Kits Description Contents DVKI Vertical Vent Kit - 17 1/2’ One piece of 35’ FlexVent (split for 17 1/2’ vent run), Round Cap, Flashing, connectors, and clamps. Recommended when installing to an existing round fireplace chimney pipe. DVVK3FV Vertical Vent Kit - 25’ Two pieces of 25’ FlexVent, Rectangle Cap, Flashing, connectors, and clamps Recommended when installing to a square or rectangular clay flue. DVK35 Vent Extension Kit 35’ flex vent extension section with 2 connectors and 4 clamps Note: When installing vent caps, special locally made flashings may be required to properly seal the vent system to the existing chimney termination. Page 6 23015-3-0707 23015-3-0707 Page 7 FIREPLACE INSERT DIMENSIONS Figure 1 When planning a fireplace insert installation, it’s necessary to determine: • The vent system configuration to be used. • Gas supply piping. • Whether optional accessories - devices such as a wall switch or remote control - are desired. • Electrical supply requirements for blower. • Proper opening size of fireplace required for installation of the fireplace insert. DV FIREPLACE INSERT DIMENSIONS MODEL A B C D E F G H I J K L M N DV25IN 19 3/8” 28 14 1/2” 11 1/8” 25 1/4” 12 3/4” 17” 18 5/16” 27” 6 3/4” 9” 20” 25 3/8” 40” DV33IN 22 3/8” 31 16 14 1/8” 28 1/4” 14 1/4” 18 3/4” 21 5/16” 30” 8 1/4” 10 1/2” 21 1/2” 28 3/8” 43” DV35IN 24 3/8” 34 16 16 1/8” 31 1/4” 14 1/4” 21 3/4” 23 5/16” 33” 8 1/4” 10 1/2” 23” 30 3/8” 46” A D C B Figure 2 Fireplace Opening Dimensional Information/Sizing MINIMUM FIREPLACE OPENING DIMENSIONS MODEL NO. HEIGHT A* FRONT WIDTH B DEPTH C REAR WIDTH D DV25IN 18 3/8” 27 1/2” 12 3/4” 17 1/4” DV33IN 21 3/8” 30 1/2” 14 1/4” 19” DV35IN 23 3/8” 33 1/2” 14 1/4” 22” *Note: If the fireplace lintel is wider than 8” (203mm), the height of the fireplace opening must be increased a few inches to allow for a gradual offset in the exhaust and/or intake vent pipes. Page 8 23015-3-0707 MANTLE AND TRIM CLEARANCES COMBUSTIBLE MANTEL/TRIM AREA 12” 10” 1 3/4” 23” 11” Combustible Material No greeting cards, stockings or ornamentation of any type should be placed on or attached to the fireplace. The flow of heat can ignite combustibles. Figure 4 8” MINIMUM CLEARANCE TO PERPENDICULAR COMBUSTIBLE SIDE-WALL (FROM EDGE OF DOOR FRAME) Figure 3 23015-3-0707 Page 9 Figure 5 The gas pipeline can be brought in through the right or left side of the appliance. The insert has a Flexline with shutoff valve located on the right side when facing the unit. See Figures 5 and 6. Consult the current National Fuel Gas Code, ANSI Z223.1 CAN/CGA-B149 (.1 or .2) installation code. Installing the Main Gas Cock Each appliance should have its own manual gas cock. A manual main gas cock should be located in the vicinity of the unit. Where none exists, or where its size or location is not adequate, contact your local authorized installer for installation or relocation. Compounds used on threaded joints of gas piping shall be resistant to the action of liquefied petroleum gases. The gas lines must be checked for leaks by the installer. This should be done with a soap solution watching for bubbles on all exposed connections, and if unexposed, a pressure test should be made. Never use an exposed flame to check for leaks. Appliance must be disconnected from piping at inlet of control valve and pipe capped or plugged for pressure test...