Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
INTRODUCTION 2 2. FEATURES 2 3. UNPACKING AND ASSEMBLY 4 4. KEROSENE (1-K OR NO. 1 FUEL OIL) 6 5. OVERVIEW OF HEATER DESIGN 7 6. FUELING YOUR HEATER 8 7. OPERATION 8 8. LONG TERM STORAGE OF YOUR HEATER 9 9. MAINTENANCE 9 10. TROUBLE SHOOTING GUIDE 16 11. WIRING DIAGRAM 17 12. SPECIFICATIONS 19 13 EXPLODED PARTS DRAWING 20 14. PARTS LIST 22 1. INTRODUCTION Please read this USER’S MANUAL carefully. It will show you how to assemble, maintain, and operate the heater safely and efficiently to obtain full benefits from its many built-in features. 2. FEATURES Hot Air Outlet Upper Shell Lower Shell Fuel Tank Side Cover Power/Reset Switch Handle Fan Guard Fuel Cap Fuel Gauge Power CordLamp Thermostat Knob Figure 1. RMC-KFA45T / RMC-KFA65T MODELS 2 NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! Hot Air Outlet Handle Upper Shell Lower Shell Fuel Gauge Side Cover Power/Reset Switch Upper Shell Fan Guard Power Cord Fuel Tank Fuel Cap Thermostat Knob Lamp Figure 2. RMC-KFA120T / RMC-KFA170T MODELS Hot Air Outlet Handle Upper Shell Lower Shell Fuel Gauge Side Cover Power/Reset Switch Upper Shell Fan Guard Power Cord Fuel Tank Fuel Cap Thermostat Knob Lamp Figure 2. RMC-KFA210T MODEL 3 NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! 3. UNPACKING AND ASSEMBLY 1. REMOVE THE HEATER AND ALL PACKING MATERIALS FROM THE BOX. (Fig. 4 and 5) NOTE: Save the shipping carton and packing materials for future storage. RMC-KFA45T/65T RMC-KFA120T RMC-KFA170T RMC-KFA210T Wheel Support Frame No Yes Yes Yes Wheels No Yes Yes Yes Handle Yes Yes Yes Yes Screws and Nuts No Yes Yes Yes Axle No Yes Yes Yes Split Pin and Washer No Yes Yes Yes Screws Yes No No No Figure 4. RMC-KFA45T / RMC-KFA65T MODELS Handle Screws Figure 5. RMC-KFA120T / RMC-KFA170T / RMC-KFA210T MODELS Wheels Split pin And Flat Washer Screws And Nuts Handle Wheel Support Frame Axle 4 NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! 2. ASSEMBLY A. For RMC-KFA45T/RMC-KFA65T Models only (Figure 6) Tools Required • Medium Phillips Screwdriver 1. Align the holes on the upper shell with the 2 mounting holes on the handle as shown in Figure 6. 2. Secure each hole with a screw. B. For RMC-KFA120T / RMC-KFA170T / RMC-KFA210T Models only (Figure 7) These models are furnished with wheels and handles. Wheels, handles, and the mounting hardware are found in the shipping carton. Tools Required • Medium Phillips Screwdriver • 5/16"(M5) open or Adjustable Wrench. Use US(INCH) Screws Nuts • Long Nose Pliers 1. Slide axle through wheel support frame. Install wheels on axle. NOTE: When installing wheels, point extended hub of wheels toward wheel support frame (see Figure 7) 2. Place Flat washers and split pin on axle ends and bend split pins with long nose pliers to secure. 3. Place heater on wheel support frame. Make sure air inlet end (rear) of heater is over wheels. Align the holes on fuel tank flange with holes on wheel support frame. 4. Position the handle on top of fuel tank flange. Insert screws through handles, fuel tank flange, and wheel support frames as shown in Figure 7 and attach nut finger tight after each screw is inserted. 5. After all screws are inserted, tighten nuts firmly. CAUTION: DO NOT OPERATE heater without support frame assembled to tank. Screw Handle Figure 6 5 NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! Screw Air Inlet Axle Split pin Flat Washer Wheel Nut Wheel Support Frame Fuel Tank Flange Hot Air Outlet Handle Extended Hub Figure 7. Wheel and Handle Assembly, RMC-KFA120T/RMC-KFA170T/RMC-KFA210T MODELS ONLY NOTE: Heater should be inspected before each use, and at least annually by a qualitied service person. 4. KEROSENE (1-K) It is EXTREMELY IMPORTANT for the proper operation of this heater that you use the correct grade of kerosene. The correct grade of kerosene is identified as 1-K kerosene. 1-K Kerosene has been refined to virtually eliminate contaminants such as sulphur, which can cause a rotten egg odor during operation of the heater. #1 fuel oil may be used if 1-K kerosene is not available. KEROSENE SHOULD ONLY BE STORED IN A BLUE CONTAINER THAT IS CLEARLY MARKED “KEROSENE”. NEVER STORE KEROSENE IN A RED CONTAINER. Red containers are associated with gasoline. NEVER store kerosene in the living space. Kerosene should be stored in a well ventilated place outside the living area. NEVER use any fuel other than 1-K kerosene (#1 fuel oil is an acceptable substitute.) NEVER use fuel such as gasoline, benzene, alcohol, white gas, camp stove fuel, paint thinners, or other oil compounds in this heater. These are volatile fuels that can cause an explosion or uncontrolled flames. NEVER store kerosene in direct sunlight or near a source of heat. NEVER use kerosene that has been stored from one season to the next. Kerosene deteriorates over time. “OLD KEROSENE” WILL NOT BURN PROPERLY IN THIS HEATER. 6 NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! 5. OVERVIEW OF HEATERS DESIGN Fuel System: This heater is equipped with an electric air pump that forces air through the...
Эта инструкция также подходит к моделям:Электрообогреватели - Dyna-Glo RMC-KFA45T, RMC-KFA65T, RMC-KFA120T, RMC-KFA170T, RMC-KFA210T (1.35 mb)
Электрообогреватели - RMC-KFA210T (1.35 mb)
Электрообогреватели - RMC-KFA65T (1.35 mb)