Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Please see page 9 "Check for Leak" for full instructions. 7-3. Put gas cylinder on the stand. rest it on of gas hose as cylinder and Ln ASSEMBLY 7-4. Lower tank over gas cylinder and down to cover base. Check for Leak Your patio heater has been checked at all factory connections for leaks, but you should always check when you attach the LPG cylinder. To check for leaks, follow these instructions: --Assemble all gas connections; --Connect regulator assembly to the propane tank; --Make sure the heater valve is turned OFF. 1) Make soapy solution by mixing 1 part liquid dish soap and 3 parts water. 2) Open the propane tank valve. 3) Spoon several drops (or use squirt bottle) of the soapy solution onto the gas hose /regulator and regulator/cylinder connection. 4) Inspect the connections and look for bubbles. 5) If no bubbles appear the connection is safe. 6) If bubble appears, there is leakage. Close the propane tank valve, and loosen and re-tighten this connection. 7) Check for leakage again. -9- ASSEMBLY 8) If bubbles still appear, close the propane tank valve and contact your gas supplier. If a leak is detected, DO NOT attempt to use the heater. MAKE SURE to check all THREE connections between the cylinder and gas line. NOTE: 1)The cylinder must be provided with a shut off valve terminating in a LPG supply cylinder valve outlet specified, as applicable, for connection NO 510 in the standard for compressed gas cylinder valve outlet and inlet connections, ANSI/CGA-v-1. 2) The cylinder supply system must be arranged for vapor withdrawal. 3) The cylinder used must include a collar to protect the cylinder valve. Annually check operation: A. Lift the tank housing up above the LPG cylinder and rest it on the support leg assembly. B. Open the propane tank valve. -10- ASSEMBLY C. Spoon several drops(or use squirt bottle)of the solution onto gas hose connection and pilot connection. D. Inspect the connections and look for bubbles. E. If no bubbles appear, the connection is safe. F. If bubbles appear, there is a leak. Close the propane tank valve and loosen and re-tighten this connection. G. Check for leaks again. H. If bubbles still appear, close the propane tank valve and call the gas supplier. DO NOT attempt to use the heater. OPERATION WARNING: DO NOT attempt to operate heater until you have read and understand all precautions. Failure to do so can result in serious personal injury, death or property damage. Before Turning Gas Supply ON. Your heater was designed and approved for OUTDOOR USE ONLY. DO NOT use it inside a building or any other enclosed area. Make sure surrounding areas are free of combustible materials such as gasoline and other flammable vapors or liquids. Ensure that there is no obstruction to air ventilation. Be sure all gas connections are tight and there are no leaks. Be sure the access panel is clear of debris. Be sure any component removed during assembly or servicing is replaced and fastened prior to starting. Before Lighting Heater should be thoroughly inspected before each use. Have a qualified service person inspect the heater at least annually. If relighting a hot heater, always wait at least 5 minutes. -11- OPERATION LIGHTING INSTRUCTIONS TO TURN ON THE HEATER: 1. Turn the control knob "OFF". 2. Open gas valve fully. 3. Press and turn the control knob to "HI" position (counterclockwise 90°). Press down the control knob and hold 3-5 seconds. While holding down the control knob, press the igniter button several times until the pilot flame ignites. Hold the knob about 30 seconds and then release. Note: If the pilot flame does not light or it goes out, repeat Step 3 above. NOTE: • If a new tank has just been connected,please allow at least one minute or more for the air in the gas pipeline to purge out through the pilot hole, or simply do Step 3. • When lighting the pilot flame make sure that the variable control knob is continuously depressed while pressing the igniter button. Variable control knob can be released after the pilot flame has been lit for 20^30 seconds. • Pilot flame can be watched and checked from the peephole located on the base of burner. • If the pilot flame does not light or it goes out,repeat Step 3. If the burner flame goes out accidentally or it is blown out by wind,turn off the heater and wait at least 5 minutes or more to let the gas dissipate before relighting to avoid possible gas explosion Repeat steps 2 to 4. TO TURN OFF THE HEATER. 1. Press and turn the control knob to "OFF" position. 2. Turn off the valve on the gas cylinder and disconnect the cylinder. control knob Igniter WARNING FOR YOUR SAFETY If at any time you are unable to light burner and smell gas, wait 5 minutes to allow gas to dissipate before attempting to light heater. If after 1 minute, you are unable to light burner, wait 5 minutes and allow flammable vapors to dissipate before attempting to light heater again. control knob ...
Эта инструкция также подходит к моделям:Электрообогреватели - FireSense 60763 (4.65 mb)
Электрообогреватели - PH01-SS (4.65 mb)