Оценок - , средний балл:
(
)
)
Производитель: Enerco
Размер: 1.52 mb
Название файла:
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
NO. REQ’D STOCK NO. DESCRIPTION 1 1 00024 COMB. GAS VALVE (PP) NG. 1/2x1/2 NPT 2 1 00025 COMB. GAS VALVE (PP) LP. 1/2x1/2 NPT 3 1 05577 ORIFICE PILO T LP 4 1 05573 ORIFICE PILO T NG 5 1 09360 THERMOCOUPLE PP HONEYWEL 6 1 10367 THERMOSTAT “PP” HEAT STAR 7 1 11405 PILO T-PP-4K, 8K HTR NG 7 1 11408 PILO T-PP-4K, 8K HTR LP 8 1 16425 FLE X PILO T TUBE WITH FITTINGS NPP 1 4 5 6 7 8 LPP 2 3 5 6 7 8 NOTE: 1 – WHEN ORDERING SPARE PARTS ALWAYS GIVE HEATER MODEL NO., STOCK NO., SERIAL NO., AND TYPE OR GAS USED. 2 – WHEN DISASSEMBLING PARTS FROM HEATER FOR REPAIR, CAREFULL Y NOTE ORIENTATION OF PARTS, AND THEN REVERSE PROCEDURE WHEN ASSEMBLING. 1 4 5 6 7 8 2 3 1 5 3 6 2 8 4 5 7 Enerco Group, Inc. | Gas-Fired Infra-Red Space Heaters 13 Operating Instructions and Owner’s Manual SUGGESTED HANGING METHOD MODEL : 4000, 8000, 9000, MH40 TYPICAL BEA M MOUNT Figure 4 CEILING SIDE WALL FLO R HORI ZONTAL MOUNT BACK SEE INSTALL ATION INSTRUCTIONS FOR DETAILE D CLE ARANCES INFORMATION CLEARANCES TO COMBUSTI BLES BELO W TOP BEAM CLAMP THREADED ROD WHEN ANGLE MOUNTING ELE VATE ONLY DESIGNATED SIDE OF HEATER Figure 5 ANGLE IRON SEE CHAIN KIT #17374 or thr ead ed rod FROM HORIZONTAL MAXIMUM 45° TYPICAL WAL MOUNT HEATER SIDE REFLE CTOR MUST BE PARALLEL TO THE FLO R mo unting SEE CHAIN KIT #17374 or thr ead - ed rod F114581 Hanging Brack et Kit F114581 Hanging Brack et Kit or chain kit 17374 recomm end using heat er hanging brack et f114581 Enerco Group, Inc. |Gas-Fired Infra-Red Space Heaters 14 Operating Instructions and Owner’s Manual Figure 6 LO W PRESSURE, MAIN GAS LINE see figur e 2 for pr oper in let pr essur es FOR HIGHER PRESSURES THAN SHOWN ABOVE CONTACT FACTORY FOR PROPER REGULATOR ON THREADED PIPES USE A PIPE COMPOUND WHICH IS RESISTANT TO THE ACTION OF ALL GASES MUST BE RESISTANT TO PROPANE TYPICAL LOW PRESURE STANDARD INSTALATI ON HEATER MOUNTING HOLE S-4 REQ’D SIDE VIEW . PSI MAX. SHUT-OFF VALVE TEE DRIP LE G CAP HIG H ALTITUDE OPERATI ON 1. Please contact the factory for a detailed High Altitude Conversion Kit to suit your specific need. 1.1 Be prepared to answer factory questions regarding: Type of fuel for the proposed appliance conversion, gas pressure available at site, and specific altitude at site. 2. “The conversion shall be carried out by a manufacturer’s authorized representative, in accordance with the requirements of the manufacturer, provincial or territorial authorities having jurisdiction and in accordance with their requirements.” 3. High Altitude Conversion Kits will include high altitude rating plate with stamped data, necessary orifices or burner as required for specific need and additional installation instructions. 4. In Canada, Heater installations at High Altitudes shall comply with the applicable construction provisions of the current standard CAN1-2.17, gas fired appliances for use at high altitudes. rigid or flexib le gas lin e to heat er pip e nip le Enerco...
Эта инструкция также подходит к моделям:Электрообогреватели - HS4040 (1.52 mb)
Электрообогреватели - HS8060 (1.52 mb)
Электрообогреватели - HS9120 (1.52 mb)