Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
Fully programmable, the Model RCL-T allows for virtual command over nearly all operational and temperature variables, using the hand held remote control transmitter. The Model RCL-T (Deluxe) remote control system is installed in the same manner as the standard system, may be operated with electronic and millivolt systems with either natural or propane gas. The RCL-T comes complete with detailed operating instructions. Wall Thermostat Kit* A wall thermostat kit is available for use with these appliances. The wall thermostat is designed to be wired directly to the appliance millivolt gas control circuit and provide automatic On/Off control of the appliance to maintain a desired temperature within the room. Wall Switch Kit* An optional wall switch kit can be installed along with all vent-free appliances. The kit consists of a standard UL wall switch with cover plate. This kit provides for remote (wall) operation of the appliance. Replace the wall switch and cover plate of this kit with the components of the RCK and you can have true remote control of your vent-free appliance, turning it on and off from your favorite easy chair. The wall switch kit should be installed along with the appliance. *Use 18GA, solid two conductor wire to connect these kits to the appliance. NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. ACCESSORY COMPONENTS Remote Control System Standard H0249 RCL Remote Control System Deluxe H0251 RCL-T Thermostat 89L36 FWTK Wall Switch Kit 85L87 FWSK MILLIVOLT WIRING DIAGRAM PILOT (O.D.S.) ASSEMBY THERMOPILE WHITE WHITE RED BLACK OFF ON MILLIVOLT VALVE ON/OFF SWITCHAND PILOT IGNITOR OPTIONAL REMOTE CONTROL (MILLIVOLT) IGNITION WIRE MILLIVOLT WIRING DIAGRAM PILOT (O.D.S.) ASSEMBY THERMOPILE WHITE WHITE RED BLACK OFF ON MILLIVOLT VALVE ON/OFF SWITCHAND PILOT IGNITOR OPTIONAL REMOTE CONTROL (MILLIVOLT) IGNITION WIRE Model No. BTU/HR Input Gas Type Ignition Regulator Pres. Setting Gas Inlet Pressure* Valve Operation Orifice Size SHGL - 18VN-R 36,000 24,000 Natural Piezo 1.6 – 3.5" w.c. Max. 10.5" w.c. Min. 5.0" w.c. Millivolt 0.113 SHGL - 18VP-R 36,000 24,000 Propane/LPG Piezo 6.3 – 10.0" w.c. Max. 13" w.c. Min. 11" w.c. Millivolt 0.069 SHGL - 24VN-R 39,000 28,000 Natural Piezo 1.6 – 3.5" w.c. Max. 10.5" w.c. Min. 5.0" w.c. Millivolt 0.119 SHGL - 24VP-R 39,000 29,000 Propane/LPG Piezo 6.3 – 10.0" w.c. Max. 13" w.c. Min. 11" w.c. Millivolt 0.072 * For the purpose of input adjustment. NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. MANUAL VALVE PILOT ASSY IGNITION WIRE MANUAL VALVE PILOT ASSY IGNITION WIRE MANUAL WIRING DIAGRAM VENTED/UNVENTED GAS LOG APPLIANCE TECHNICAL CHART FOR MANUAL LOG SET Model No. BTU/HR Input Gas Type Ignition Regulator Pres. Setting Gas Inlet Pressure* Valve Operation Orifice Size SHGL - 18MN-R 36,000 25,000 Natural Piezo 3.5" w.c. Max. 10.5" w.c. Min. 5.0" w.c. Manual 0.126 SHGL - 18MP-R 36,000 27,000 Propane/LPG Piezo 10.0" w.c. Max. 13" w.c. Min. 11" w.c. Manual 0.071 SHGL - 24MN-R 39,000 26,000 Natural Piezo 3.5" w.c. Max. 10.5" w.c. Min. 5.0" w.c. Manual 0.136 SHGL - 24MP-R 39,000 31,000 Propane/LPG Piezo 10.0" w.c. Max. 13" w.c. Min. 11" w.c. Manual 0.074 * For the purpose of input adjustment. NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. OPERATING INSTRUCTIONS — MANUAL CONTROL MODELS FOR YOUR SAFETY READ BEFORE LIGHTING LIGHTING INSTRUCTIONS 1. Stop! Read the safety information above. 2. Make sure manual shut-off valve is fully open. 3. Refer to Figure 14 to locate gas control knob and piezo. 4. Depress control knob in and turn clockwise to the “OFF” position (Figure 15). 5. Wait 5 minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information above. If you do not smell gas, go to the next step. 6. The pilot is located on the right side in front of the burner (Figure 16). 7. Depress control knob in and turn counterclockwise to the “IGN” position (Figure 17). Press the control knob all the way in for 5 seconds. Note:If you are running the heater for the first time it will be necessary to press the control knob all the way in for 30 seconds to allow air to bleed out of the gas piping. MANUAL MATCH LIGHTING PROCEDURE — EMERGENCY ONLY 1. If the pilot cannot be lit with the piezo igniter, the heater can be manually lit with a match. 2. With the right hand, depress and turn the control knob counterclockwise to the “IGN” position. Hold in the knob. TO TURN OFF GAS TO APPLIANCE 1. Depress and turn control knob clockwise to the “OFF” position (Figure 17). 3. Light the match and hold the flame to the end of the pilot and ignite the pilot. 4. Continue to hold control knob for an additional 10 seconds to insure pilot remains lit. 5. Release the control while turning control knob to desired setting. 8. With the control knob pressed in, push in and release the piezo igniter button to light the pilot. 9. Hold the control knob in for a further 10 seconds to prevent the flame failure detector from shutting off the gas while...
Эта инструкция также подходит к моделям:Электрообогреватели - SHGL-18MN-R (821.19 kb)
Электрообогреватели - SHGL-18VN-R (821.19 kb)
Электрообогреватели - SHGL-18VP-R (821.19 kb)
Электрообогреватели - SHGL-24MN-R (821.19 kb)