Оценок - 5, средний балл: 4.2
(
)
)
|
Фрагмент инструкции
Montpelier Wood Insert NOTE: Cast iron parts can be heavy, an assistant would be advisable. CAUTION: Porcelain enamel is fragile. The finish can be easily damaged if castings are not handled carefully. Always place castings on a protective surface, such as a towel, blanket or carpet. Table of Contents Traditional Cast Surround Models: MEAD3CB, MEAD3EB, MEAD3BS...................................................................2 Small Cast Profile Surround Models: CAPCB, CAPEB ...............................................................................................4 Bevel Cast Trim Surround Model: LHEABSL ...........................................................................................................6 Steel Surround Panels Models: LHE30SSB, LHE30SLB, LHE30SLGA ............................................................. 6 Georgian Cast Surround Models: 30DVSGTKCB, 30DVSGTKB ........................................................................... 7 Replacement Parts...........................................................................................................10 30004451 7/08 Rev. 2 Traditional Cast Surround Models: MEAD3CB, MEAD3EB, MEAD3BS Read these instructions before beginning the installation. Check Contents of Shipping Carton Compare contents of carton in Figure 2 with actual parts received. If any parts are missing or damaged, contact your dealer before starting the installation. Surround parts: 1. Right column 2. Mantel 3. Left column 4. Lower bracket (2) 5. Upper bracket (2) (not used on Montpelier Insert) 6. Switch housing (not used on Montpelier Insert) 7. Hex head bolt, 1/4”- 20 x 3/8” (4) 8. Phillips pan head bolt, 1/4” x 3/8” (6) 9. Washers, 7/8” (4) KT1011 Fig. 1 Front view of surround assembly. General Information KT1011 The assembly includes three (3) cast iron surround panels, lower brackets and hardware. The upper brackets and switch housing are not used with the Montpelier Wood Insert. traditional surround 3/08 djt Install the Traditional Cast surround after all other instal lation work has been completed, thoroughly checked, and tested for proper operation, leaks and installation requirements. Tools required: Phillips screwdriver, 7/16” wrench. 4 4 2 5 8 8 1 6 79 9 7 3 8 Damper Tabs supplied in Finish Bag of Insert KT1012 Fig. 2 Rear view of surround assembly. Assembling the Surround Lay out the parts, face down, on a flat padded surface. (Fig. 2) KT1012 1. Align the holes in the top flanges of the left and right Assemble columns with the drilled and tapped bosses onto the surround left and right ends of the mantel. 3/08 djt 2. Attach the mantel to the columns with four (4) 1/4”20 hex bolts and washers. 3. Attach two (2) damper tabs (supplied in Finish Bag of Montpelier Insert) using two (2) 1/4” x 3/8” Phillips pan head bolts to backside of center mantel. (Fig. 2) NOTE: Make sure damper tabs hang down. 4. Attach the two (2) lower brackets to the bottoms of the columns with two (2) 3/8” Phillips pan head bolts each. (Fig. 2) NOTE: When positioning the right column lower bracket, make sure one of the hooked flanges is in the upper right hand corner and facing away from you. (Fig. 2) The left column lower bracket is the opposite way. 30004451 3 Attach the Surround to the Montpelier 1. Once the insert is installed and tested for proper operation as directed, stand the Traditional Cast Surround in front of the insert. 2. Position the surround in front of the insert and, with the help of an assistant, gently lift the surround up and over the top sheet metal flange. Make sure the damper tabs are positioned on the back side of the flange. At the same time, align the bottom brackets through the slots on the side flanges. (Fig. 3) 3. Adjust the surround, left to right, so there is an equal reveal and secure by applying downward pressure until the brackets have engaged onto the insert. (Fig. 3) Assembly complete. ............ .............................. ........ Side Flange Top Flange Fig. 3 Lift surround up and over top flange and up and through side flange holes. KT1013 4 30004451 Small Cast Profile Surround Models: CAPCB, CAPEB Read these instructions before beginning the installation. CAUTION: Always place castings on a flat protected work surface, such as a towel, blanket or carpet. These instructions are for the assembly and installation of the Small Cast Profile Surround to the Montpelier Insert. Carefully unpack and inspect all components from the shipping box. Report any missing or damaged parts to your dealer immediately. Install trim kit after all other insert installation work has been completed, thoroughly checked and tested for proper operation, leaks and installation requirements. Tools required: Tape measure. Surround Parts Column Right Assembly Column, right Boot, right Slider clip, right Bracket, On/Off switch (not used on Montpelier Insert) 1/4-20 Round head screw (2) 1/4-20 Wing screw (2) 1/4 Flat washer (3) Column Left Assembly Column, left Bo...
Эта инструкция также подходит к моделям:Электрообогреватели - Montpelier Wood Insert MEAD3CB (5.21 mb)
Электрообогреватели - Montpelier Wood Insert MEAD3EB (5.21 mb)