Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
WARNING: Be careful when attempting to manually ignite this heater. Holding in the control know for more than 10 seconds before igniting the gas will cause a ball of flame upon ignition. Have a question or are having problems visit or call 1.800.762.1142. Note: the burner may be noisy when initially turned on. To eliminate excessive noise from the burner, turn the control knob to the pilot position. Then, turn the knob to the level of heat desired. When heater is ON: Emitter screen will become bright red due to intense heat. The color is more visible at night. Burner will display tongues of blue and yellow flame. These flames should not be yellow or produce thick black smoke, indicating an obstruction of airflow through the burners. The flame should be blue with straight yellow tops. If excessive yellow flame is detected, turn off heater and visit or call 1.800.762.1142. Re-lighting Note: For your safety, control knob cannot be turned “OFF” without first depressing control knob in PILOT position and then rotating it to “OFF”. 1. Turn control knob to “OFF”. 2. Wait at least 5 minutes, to let gas dissipate, before attempting to relight pilot. 3. Repeat the “Lighting” procedure. Shut Down 1. Turn control knob clockwise to pilot. (Normally, burner will make a slight popping sound when extinguished.) Burner will extinguish but pilot will remain “ON”. 2. To extinguish pilot, depress control knob and continue to turn it clockwise to “OFF”. 3. Turn tank valve to “CLOSED” and disconnect regulator when heater is not in use. Note: After use, some discoloration of the emitter screen is normal. Cleaning and Care CAUTION: All cleaning and maintenance should be done when patio heater is cool and with the fuel supply disconnected. CAUTION: DO NOT clean any patio heater part in a self cleaning oven. The extreme heat will damage the finish. Notices 1. Abrasive cleaners will damage this product. 2. Never use oven cleaner to clean any part of heater. 3. Do not clean any heater part in a self cleaning oven. The extreme heat will damage the finish. 4. More frequent cleaning may be required as necessary. It is imperative that control compartment, burners and circulating air passageways of the heater be kept clean. 5. Spiders and insects can create a dangerous condition that may damage heater or make it unsafe. Keep burner area clean of all spiders, webs, or insects. Clean burner holes by using a heavy-duty pipe cleaner. Compressed air may help clear away smaller particles. 6. Inspect heater before each use. 7. Have heater inspected annually and repairs should be made by a qualified service person. 8. Check heater immediately if any of the following conditions exist: a. The smell of gas in conjunction with extreme yellow tipping of burner flames. b. Heater does not reach proper temperature. Note: At temperatures less than 40.F, heat output will be reduced. c. Heater’s glow is excessively uneven d. Burner makes popping noises during use. Note: A slight pop is normal when burner is extinguished. 9. Carbon deposits may create a fire hazard. Keep dome and emitter clean at all times. 10. Do not clean heater with combustible or corrosive cleaners. Use warm, soapy water. 11. Do not paint engine, engine access panel or dome. 12. This heater should be thoroughly cleaned on a regular basis. 13. After a period of storage and/or nonuse, check for leaks, burner obstructions and inspect for any abrasion, wear, cuts to the hose. Cleaning Surfaces 1. Wipe surfaces clean with mild dishwashing detergent or baking soda. 2. For stubborn surfaces use a citrus based degreaser and a nylon scrubbing brush. 3. Rinse clean with water. Note: While cleaning your unit, be sure to keep the area around the burner and pilot assembly dry at all times. Do not submerge the control valve assembly. If the gas control is submerged in water, do NOT use it. It must be replaced. Proper flame height. X LP Gas Line XXXXX LP Gas Tank Valve View Hole Control Knob Maintenance To enjoy years of outstanding performance from your heater, make sure you perform the following maintenance activities on a regular basis: 1. Keep exterior surfaces clean. 2. Air flow must be unobstructed. Keep controls, burner, and circulating air passageways clean. Signs of possible blockage include: Gas odor with extreme yellow tipping of flame. Heater does NOT reach the desired temperature. Heater glow is excessively uneven. Heater makes popping noises. Note: In a salt-air environment (such as near an ocean), corrosion occurs more quickly than normal. Frequently check for corroded areas and repair them promptly. TIP: Use high-quality automobile wax to help maintain the appearance of your heater. Apply to exterior surfaces from the pole down. Do not apply to emitter screen or domes. Storage Between uses: 1. Turn Control Knob OFF. 2. Disconnect LP source. 3. Store heater upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, hai...
Эта инструкция также подходит к моделям:Электрообогреватели - UB093-003-73-19 (2.96 mb)