Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
It is essential to keep the heater’s valve compartment, burners, and circulating air passages clean. Inspect heater before each use. Installation and repair should be done by a qualified service person. Do not alter heater in any manner. Do not use the heater unless it is COMPLETELY assembled and all parts are securely fastened and tightened. This heater should be thoroughly inspected before each use. Clean and inspect the hose before each use of the appliance. If there is evidence of abrasion, wear, cuts, or leaks, the hose must be replaced prior to the appliance being put into operation. Use only the regulator and hose assembly provided. The replacement regulator and hose assembly shall be that specified by the manufacturer. Inspect heater before each use. If a damaged part is detected, do not operate until an original equipment replacement part has been properly installed. Use only Blue Rhino Global Sourcing, Inc. factory authorized parts. The use of any part that is not factory authorized can be dangerous. This will also void your warranty. Dome and burner are extremely hot to the touch during operation. Never touch the dome or burner while the heater is operating. Wait for unit to cool down (approximately 45 minutes) after use. During operation, do not touch burner assembly. The surface of heater’s emitter can reach temperatures approaching 1600.F. Do not install or use in or on boats or recreational vehicles. Do not use heater in winds that exceed 10 m.p.h.. Unit will operate at reduced efficiency below 40.F (5.C). Do not leave a lit heater unattended, especially keep children and pets away from heater at all times. Always use extreme caution when near heater. Alert both children and adults to the hazards of high temperatures, especially to avoid burns or clothing catching fire. Do not attempt to move heater when in use. Allow the heater to cool before moving or storing. Storage of heater indoors is permissible only if the tank is disconnected, removed from the heater and properly stored outdoors. Do not attempt to disconnect the gas regulator from the tank or any gas fitting while the heater is in use. Always place your heater on a hard, level surface. Use extreme caution on wooden decks. Move gas hoses as far away as possible from hot surfaces. Keep all electrical cords away from a hot heater. Do not use heater for indoor cooking or heating. TOXIC fumes can accumulate and cause asphyxiation. Keep sprinklers and other water sources away from burner and controls. Do not hang clothing or other flammable materials either on or near heater. Always allow heater to cool before attempting service. Any guard or other protective device removed for servicing the heater must be replaced prior to operating the heater. Certain materials or items, when stored under heater, will be subjected to radiant heat and could be seriously damaged. After a period of storage and/or nonuse, check for leaks, burner obstructions and inspect for any abrasion, wear, cuts to the hose. If at any time you are unable to light burner and smell gas, wait 5 minutes to allow gas to dissipate before attempting to light heater. Failure to not wait 5 minutes to allow the gas to clear if the heater does not light, may result in an explosive flame-up. Be careful when attempting to manually ignite this heater. Holding in the control knob for more than 10 seconds before igniting the gas will cause a ball of flame upon ignition. Avoid inhaling fumes emitted from the heater’s first use. Smoke and odor from the burning of oils used in manufacturing will appear. Both smoke and odor will dissipate after approximately 30 minutes. The heater should NOT produce thick black smoke. If heater is not in use, the gas must be turned off at the supply tank. Do not use this appliance without reading “Operating Instructions” in this manual. Deaths, serious injury or damage to property may occur if the above is not followed exactly. page no. Parts List 1 Finial 56-01-103 2 Dome Cap 56-01-104 3 Dome Plate 56-01-105 4 Dome Panel (3) 56-01-106 5 Dome Rib (3) 56-01-109 6 Dome Pin* (3) 56-01-459 7 Bottom Plate 56-01-110 8 Emitter Top* 56-01-399 9 Emitter Screen* 56-01-118 10 Burner* 56-01-334 11 Pilot Heat Shield* 56-01-151 12 Pilot Assembly* 56-01-127 13 Burner Orifice* 56-01-131 14 Electronic Igniter* 56-01-142 15 Igniter Button* 56-01-188 16 Control Knob* 56-01-156 17 Access Panel* 56-01-140 18 Valve* 56-01-144 19 Valve Bracket* 56-01-463 20 Tip Switch* 56-01-019 21 Valve Housing* 56-01-144 22 Gas Line 56-01-190 23 Pole 56-01-158 24 Shroud 56-01-164 25 Platform 56-01-165 26 Gas Line Clip 56-01-213 27 Leg (3) 56-01-491 28 Tank Retention Chain 56-01-186 29 Regulator/Hose Assembly 56-01-192 30 Base 56-01-196 31 Weight Plate 56-01-198 32 Wheel Hole Plug (2)* 56-01-402 * Pre Assembled Exploded View 1 2 3 5 4 6 7 8 9 10 11 12 13 14 21 15 22 20 23 19 17 18 16 24 25 26 27 29 28 32 30 31 Hardware A Screw 5/32” - 32 x 8 Stainless Steel Round Head 3 pcs B Screw 3/16” - 24 x 1...