Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
EWTR720SP Assembly Instructions 1 2 Attach Head Assembly DO NOT RETURN PRODUCT TO STORE. Note: Use the wrench to tighten nut. Do NOT over tighten. For assistance call 1.800.762.1142 toll free. Please have your owner’s manual and serial number available for reference. For Easiest Assembly: • To avoid losing any small components or hardware, assemble your product on a hard level surface that does not have cracks or openings. • Clear an area large enough to layout all components and hardware. • When applicable, tighten all hardware connections by hand first. Once the step is completed, go back and fully tighten all hardware. • Follow all steps in order to properly assemble your product. Note: Two (2) adults may be required for assembly. A x 1 Secure Inner Pole Note: Use the wrench to tighten nut. Do NOT over tighten. 3 A x 1 B x 1 page no. Contact 1.800.762.1142 for assistance. Do not return to place of purchase. Operating Instructions Cleaning and Care (continued) NOTE: Heater functions best WITHOUT an extension cord. Cleaning Surfaces If an extension cord is necessary: 1. Wipe surfaces clean with a solution of water and mild dishwashing detergent or baking soda. • Use a UL approved, 3 prong plug (grounded) cord shall be no. 16 AWG minimum size and rated not less than 1500 watts. 2. Wipe clean with damp cloth. • Never connect two or more extension cords together. Note: While cleaning your unit, be sure to keep the area around the heating element dry at all times. Do not submerge the heating element. If the heating element is submerged in water, do • Use the shortest extension cord possible. NOT use it. It must be replaced. • Keep connections dry and off the ground. • Avoid draping the electric heater cord where children or animals could encounter it. Maintenance Illustration 4 To enjoy years of outstanding performance from Before Turning “ON” your heater, make sure you perform the following maintenance activities on a regular basis: 1. Make sure all labels, packaging and protective films have been removed from the heater. 1. Keep exterior surfaces clean. 2. Heater should be thoroughly inspected before each use, and by a qualified service person at least annually. 2. Air flow must be unobstructed. Keep circulating air passages around the heating element clean. Turning “ON” Illustration 1 Replacing the Fuse 1. Plug the power cord into a dry GFI (Ground Fault Interrupter) 3 plug outlet. (Illustration 1) 1. Push the power button. (Illustration 2) 2. Push the power button. (Illustration 2) 2. Unplug the power cord from the wall outlet. Note: The red LED light will glow while the heater 3. Using a screwdriver, remove the fuse cover. is on. (Illustration 4) Note: When restarting the heating element will start up 4. Carefully remove the old fuse, and replace with the slowly before getting to full power. new fuse. (Illustration 5) Note: ONLY replace the old fuse with a While Heater is “ON” 250V 15A fuse. If heater tips over, the heater will automatically 5. Reattach the fuse cover. turn “OFF”. Note: Do not over tighten If heater tips over: 6. Follow the Turning “ON” instructions or the Storage 1. IMMEDIATLEY unplug power cord from the wall outlet. Instructions. 2. Carefully turn the heater upright. CAUTION: Dome, pole and shroud cover may be hot. Use heat resistant gloves to set heater upright. Storage 3. Inspect heater to ensure no damage. Between Uses and During Periods of Extended Inactivity or If no damage continue to next step. When Transporting: If there is damage call a qualified technician to inspect and make any necessary repairs. 1. Push the power button. (Illustration 2) Metal Screw Connecting the power cord to a dry GFI 3 plug outlet. Illustration 2 Power button 2. Unplug the power cord from the wall outlet. Do NOT use the heater if there is any sign of damage. A qualified technician should inspect 3. Store heater upright in an area sheltered from direct contact with inclement weather (such and make any nescessary repairs before the as rain, sleet, hail, snow, dust and debris). heater is used again. 4. If desired, cover heater to protect exterior surfaces and to help prevent build up in air 4. Plug the power cord into a dry GFI (Ground Fault Interrupter) 3 plug outlet. (Illustration 1) passages. 5. Push the power button. (Illustration 2) Wait until heater is cool before covering. Note: The red LED light will glow while the heater is on. Note: When restarting the heating element will start up slowly before getting to full power. Turning “OFF” 1. Push the power button. (Illustration 2) 2. Unplug the power cord from the wall outlet. Remove fuse cover Illustration 5 Remove old fuse Cleaning and Care Notices 1. Abrasive cleaners will damage this product. 2. Never use oven cleaner to clean any part of heater. 3. Do not clean any heater part in a self cleaning oven. The extreme heat will damage the finish. 4. Inspect heater before each use. 5. Have heater inspected annually and repairs should be made by a qualifi...