Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
If no bubbles appear after one minute turn LP gas tank valve to “CLOSED”, wipe away solution and proceed. Before Lighting 1. Heater should be thoroughly inspected before each use, and by a qualified service person at least annually. 2. If relighting a hot heater, always wait at least 5 minutes. 3. Inspect the hose assembly for evidence of excessive abrasion, cuts or wear. Suspected areas should be leak tested. If the hose leaks, it must be replaced prior to operation. Only use the replacement hose assembly specified by manufacturer. Lighting Note: This heater is equipped with a pilot light that allows for safer startups and shutdowns. Pilot must be lit before main burner can be started. 1. Control knob must be in the “OFF” position. (Figure 3) 2. Turn LP gas tank valve to “OPEN”. 3. Open viewing hole by sliding cover to either side. (Figure 6) 4. Push control knob in and rotate to “PILOT” position. (Figure 4) Note: For initial start or after any tank change, hold control knob in for 2 minutes to purge air from gas lines before proceeding. 5. Push-button Ignition: Immediately push igniter button a couple of times. Pilot light flame will appear and be visible through viewing hole. Electronic Ignition: Immediately push igniter button for five (5) seconds. Pilot light flame will appear and be visible through viewing hole. 6. Release control knob after 30 seconds. Pilot light will remain lit. 7. If ignition does not occur, turn control knob “OFF”, wait 5 minutes and repeat lighting procedure. 8. Turn control knob to “HIGH”. (Figure 5) Main burner will light immediately. Flame is visible through viewing hole. If not, turn control knob “OFF”, wait 5 minutes, and repeat lighting procedure. 9. If for some reason your ignitor fails to deliver a spark, your heater can be started by inserting a lit match through the pilot view hole while pushing the control knob in while in the “PILOT” position. A WARNING: Be careful when attempting to manually ignite this heater. Holding in the control knob for more than 10 seconds before igniting the gas will cause a ball of flame upon ignition. Have a question or are having problems visit or call 1.800.762.1142. Figure 1 Figure 2 Figure 3 low / BAJO high / ALTO PILOT / PILOTO push in / presione y mantenga presionado OFF / APAGADO Figure 4 low / BAJO HIGH / ALTO PILOT / PILOTO push in / presione y mantenga presionado OFF / APAGADO Figure 5 LOW / BAJO HIGH / ALTO PILOT / PILOTO push in / presione y mantenga presionado OFF / APAGADO Figure 6 Note: The burner may be noisy when initially turned on. To eliminate excessive noise from the burner turn the control knob to the pilot position, then turn the knob to the level of heat desired. When heater is ON: Emitter screen will become bright red due to intense heat. The color is more visible at night. Burner will display tongues of blue and yellow flame. Figure 7 These flames should not be yellow or produce thick black smoke, indicating an obstruction of airflow through the burners. The flame should be blue with straight yellow tops. (Figure 7) If excessive yellow flame is detected, turn off heater and visit or call 1.800.762.1142. Re-lighting Note: For your safety, control knob cannot be turned “OFF” without first depressing control knob in PILOT position and then rotating it to “OFF”. 1. Turn control knob to “OFF”. 2. Wait at least 5 minutes to let gas dissipate. 3. Repeat the “Lighting” procedure. Shut Down 1. Turn control knob clockwise to pilot. (Normally, burner will make a slight popping sound when extinguished.) Burner will extinguish but pilot will remain “ON”. 2. To extinguish pilot, depress control knob and continue to turn it clockwise to “OFF”. 3. Turn tank valve to “CLOSED” and disconnect regulator when heater is not in use. Note: After use, some discoloration of the emitter screen is normal. Cleaning and Care A CAUTION: All cleaning and maintenance should be done when patio heater is cool and with the fuel supply disconnected. A CAUTION: DO NOT clean any patio heater part in a self cleaning oven. The extreme heat will damage the finish. Notices 1. This heater should be thoroughly cleaned on a regular basis. 2. Abrasive cleaners will damage this product. 3. Never use oven cleaner to clean any part of heater. 4. More frequent cleaning may be required as necessary. It is imperative that control compartment, burners and circulating air passageways of the heater be kept clean. 5. Have heater inspected annually and repairs should be made by a qualified service person. 6. Inspect heater before each use. 7. Spiders and insects can create a dangerous condition that may damage the heater or make it unsafe. Keep burner area clean of all spiders, webs and insects. Clean burner holes by using a heavy-duty pipe cleaner. Compressed air may help clear away smaller particles. 8. Check heater immediately if any of the following conditions ...