Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
All electrical work must be done in accordance with local and/ or national electrical code as applicable. For safety, this product must be grounded. If you are unfamiliar with methods of installing electrical wiring, secure the services of a qualified electrician. 2. Turn off power at service entrance before installing, wiring or servicing this product. 3. This product is designed for horizontal ceiling installation only. Do not mount this product on a wall or sloped ceiling. 4. Do not install heater closer than 12" to any adjacent vertical surface. 5. To avoid electrical shock: • Do not install unit in a tub or shower enclosure. • Never place a switch where it can be reached from a tub or shower. 6. Provide heater with a separate 20 amp (minimum), 120 VAC circuit. 7. Do not connect heater to dimmer switch or speed control. 8. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit. 9. Please read specification label on product for further information and requirements. PLAN THE INSTALLATION This heater is intended to be used to supply supplemental heat from a ceiling location in new or existing construction. Choose a location where edge of heater will be at least 12" from any adjacent vertical surface. The heater can be operated using an ON/OFF switch, timer (Model VS62WH 60-Minute or Model VS63WH 15-Minute Timer). Purchase the control separately. Plan to supply the heater with proper line voltage and appropriate power cable for its maximum wattage rating. The heater attaches directly to a standard 3" or 4" ceiling electrical box. Refer to FIGURE 1 Follow these basic steps when installing this heater: 1. Mount electrical box in ceiling and attach power cable to it. 2. Connect wiring and fasten heater to electrical box. 3. Install grille. CEILING JOIST ELECTRICAL BOX DRYWALL CEILING HEATER FIGURE 1 INSTALLATION Refer to FIGURE 2 1. Mount electrical box. Position electrical box flush or slightly recessed in ceiling and mount it securely. Refer to FIGURE 3 2. Connect wiring. Run electrical cable into box and secure with appropriate connector. Allow 6" of wire inside box. Refer to FIGURE 4 and FIGURE 5 3. Wire the heater. Attach electrical power cable to heater. Connect black to black, white to white, and green or bare wire to ground screw. Complete the wiring by adding a wall control. Follow the pictorial or schematic diagram. Refer to FIGURE 6, FIGURE 7, and FIGURE 8 4. Attach heater to electrical box. Tuck wires up into electrical box. Fit screw heads from electrical box into appropriate keyholes, as shown. Twist heater clockwise to hold it in place. Tighten two (2) electrical box screws. Refer to FIGURE 9 5. Install grille. Use grille screw (provided) to attach grille, as shown. USE AND CARE CAUTION – DISCONNECT ELECTRIC POWER SUPPLY AT SERVICE ENTRANCE BEFORE CLEANING OR SERVICING UNIT. Cleaning: To clean the heater assembly, carefully clean through heater grille, using the round brush tool on your vacuum cleaner. Remove accumulations of dust, lint, etc., that might impede the flow of air through the heater. Such blockage will lower its efficiency and create a possible overheat condition. CAUTION – METALAND ELECTRICAL PARTS SHOULD NEVER BE IMMERSED IN WATER. FIGURE 3 FIGURE 2 BLACK BLACK GROUND WHITE GREEN OR BARE WIRE GROUND SCREW WHITE TOGGLE SWITCH TIMER OR THERMOSTAT SWITCH BOX 120 VAC 60 HZ LINE IN FIGURE 4 2 M HEATING ELEMENT BLACK BLACK GROUND WHITEBLACK WHITE GROUND WHITE 120 VAC LINE IN SWITCH BOX TOGGLE SWITCH, TIMER, OR THERMOSTAT CEILING BOX T FIGURE 9 FIGURE 8 FIGURE 7 FIGURE 6 FIGURE 5 M HEATING ELEMENT BLACK BLACK GROUND WHITEBLACK WHITE GROUND WHITE 120 VAC LINE IN SWITCH BOX TOGGLE SWITCH, TIMER, OR THERMOSTAT CEILING BOX T FIGURE 9 FIGURE 8 FIGURE 7 FIGURE 6 FIGURE 5 3 PARTS LIST 9297T - R01 WARRANTY 9297T-R01 PART DESCRIPTION NUTONE ONE YEAR LIMITED WARRANTY REF. PART NO. 1 25042-00 Ceiling Pan 2 02200-18 Motor 3 06116-00 Fan Blade 4 75075-00 Heating Assembly 5 25045-00 Grille 6 99090749 Name Plate 7 99170245 8-18 x 3/8” Slotted Screw 8 06317-00 Installation Hook 8 NuTone warrants to the original consumer purchaser of our products that such products will be free from defects in materials or workmanship for a period of one year from date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. During this one-year period, NuTone will, at our option, repair or replace, without charge, any product or part which is found to be defective under normal use and service. THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS AND TUBES. This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse, negligence, accident, improper maintenance or repair (other than by us), faulty installation or installation contrary to recommended installa...