Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
The base must be weighted to avoid tipping. 6. Use only the hose and regulator assembly provided with the heater. 7. Inspect hose assembly before each use of the heater. If there is excessive abrasion or wear, or hose is cut, replace with hose assembly listed on parts list before using heater. 8. This heater is for OUTDOOR USE ONLY, even so, make sure that there is ample fresh air ventilation. Do not use in buildings, garages or other enclosed spaces. 9. If at any time gas odor is detected, IMMEDIATELY DISCONTINUE operation until the source of gas has been located and corrected. Read Propane Safety, page 4 for additional information about detecting propane leaks. 10. Install the heater such that it is not directly exposed to water spray, rain and/or dripping water. 11. Maintain minimum clearance to people or normal combustible material (like paper) of 3.6 ft. (1100 mm) from top and 2 ft. (609 mm) from the reflector. 12. Operate only on a stable, level surface. 13. Do not spray aerosols near the heater during use or shortly thereafter. 14. Do not clean heater with combustible or corrosive cleaners. Use warm, soapy water. 15. Check control compartment burners and circulation air passageways for free air passage, make sure that there are no obstructions. These areas are a common location for spider webs, which can present a dangerous condition, damage the heater and render it unsafe for use. The heater must be checked if any of the following conditions exist: a) Gas smell along with predominate yellow tipping of the burner. b) Heater does not reach temperature. c) Uneven burner glow. d) Burner makes popping noises during nor mal use, other than during shutdown. 16. Use only soapy water (1 part liquid dishwashing detergent to 3 parts water) to conduct leak tests whenever a propane cylinder is connected. Bubbles indicate a leak. 17. Do not adjust gas regulator. If you are unsure of your appliances gas type or pressure, call a qualified service person. 18. Place the control knob on "OFF" position when heater is not in use. 19. Always disconnect the gas supply after the heater is turned "OFF". 20. Do not move, handle or service while hot or burning. 21. Allow 45 minutes to cool down after use before attempting to move heater. 22. Do not operate this appliance in windy conditions. Maximum allowable wind speed is 10 mph (16 Km/h). 23. Do not operate this appliance in temperature conditions below 40° F (5° C). 24. Keep heater away from areas where flammable liquids, vapors or solids are stored or used. 25. If operated in salt air environments, the unit will require more frequent cleaning; otherwise, the longevity of the unit will deteriorate rapidly. Use warm soapy water to clean the unit. 26. Items or material, when stored under the heater, will be subjected to radiant heat and could be seriously damaged. 27. Use only in accordance with local codes, or in the absence of local codes, with the National Fuel Gas Code ANSI Z223.1. Any guard or other protective device removed for servicing must be replaced prior to operating the heater. Surface temperatures become very hotwhenoperatingheater.Children andadultsshouldstayawaytoavoid burns or clothing ignition. Young children should be carefully supervisedwhentheyareinthearea of the heater. Clothing or other flammable materials should not be hung from the heater, or placed on or near heater. 114144-01C SAFETY INFORMATION Continued Installation and repair should be done by a qualified service person. The heater should be inspected before use and at least annually by a qualified service person. More frequent cleanings may be required as necessary. It is imperative that controlcompartments,burnersand circulating air passageways of the heater be kept clean. CAUTION: The gas pressure regulator provided with this appliancemustbeused. Thisregulatorissetforanoutputpressure of 11" W.C. (2.74 kPa). PROPANE/LP SAFETY WARNING: For outdoor use only. ASPHYXIATION HAZARD • Do not use this heater for heating human living quarters. • Do not use in unventilated areas. • The flow of combustion and ventilation air must not be obstructed. • Proper ventilation air must be provided to support the combustion air requirements of the heater being used. • Refer to the Specifications, page 2, heater data plate or contact DESAHeating Products to determine combustion air ventilation requirements of the heater. • Lack of proper ventilation air will lead to improper combustion. • Improper combustion can lead to carbon monoxide poisoning leading to serious injury or death. Symptom of carbon monoxide poisoning can include headaches dizziness and difficulty in breathing. ASSEMBLY INSTRUCTIONS Tools Required: • #2 Phillips Head Screwdriver 1 • Adjustable Wrench 2 Inspect heater components for possible shipping damage. If any is found, immediately notify the dealer. Check to make sure that all components are included with your heater (see pages 10 and 11). POLE ASSEMBLY 1. Attach legs to base ...