Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
13. Replace fan guard and upper shell. Combustion Chamber Fuel Line Hose Air Line Hose Nozzle Assembly Figure 24 - Removing Air and Fuel Line Hoses, 30,000 BTU/Hr Model Nozzle Assembly Burner Strap Figure 25 - Removing Nozzle Assembly, 30,000 BTU/Hr Model Nozzle Nozzle Face Fuel line Fitting Nozzle Seal Nozzle Adapter Air lineFitting Figure 26 - Nozzle and Nozzle Adapter, 30,000 BTU/Hr Model 15 Nozzle (70/90,000 BTU/Hr Models) 1. Remove upper shell (see page 10). 2. Remove fan (see page 19). 3. Remove fuel and air line hoses from burner head. 4. Remove spark plug wire from spark plug. 5. Remove spark plug from burner head using 13/16" open-end wrench. 6. Remove three screws using 5/16" nut-driver and remove burner head from combustion chamber. 7. Place burner head into vise and lightly tighten. 8. Carefully remove nozzle from burner head using 5/8" socket wrench (see Figure 28). 9. Blow compressed air thru face of nozzle. This will free any dirt in nozzle area. 10. Inspect nozzle seal for damage. 11. Replace nozzle into burner head and tighten firmly (80-110 inch-pounds/9.112.4 n-m). 12. Attach burner head to combustion chamber. 13. Install spark plug in burner head. 14. Attach spark plug wire to spark plug. 15. Attach fuel and airline hoses to burner head. 16. Replace fan (see page 19). 17. Replace fan guard and upper shell. Combustion Chamber Burner Head Air Line Hose Fuel Line Hose Screw Spark Plug Wire Spark Plug Figure 27 - Removing Burner Head, 70/90,000 BTU/Hr Models Nozzle Face Fitting Nozzle Burner Head Air line Fuel line Fitting Nozzle Seal Figure 28 - Removing Nozzle, 70/90,000 BTU/Hr Models 16 Nozzle (150,000 BTU/Hr Model) 1. Remove upper shell (see page 10). 2. Remove fan (see page 19). 3. Remove spark plug wire from spark plug. 4. Remove spark plug from burner head using 13/16" open-end wrench. 5. Loosen flare nut using 3/4" open-end wrench. Push fuel tube down. 6. Remove air line hose from burner head. 7. Remove three screws using 5/16" nut-driver and remove burner head from combustion chamber. 8. Place burner head into vise and lightly tighten. 9. Carefully remove nozzle from burner head using 5/8" socket wrench (see Figure 30). 10. Blow compressed air thru face of nozzle. This will free any dirt in nozzle area. 11. Inspect nozzle seal for damage. 12. Replace nozzle into burner head and tighten firmly (80-110 inch-pounds/9.112.4 n-m). 13. Attach burner head to combustion chamber. 14. Install spark plug in burner head. 15. Attach spark plug wire to spark plug. 16. Attach fuel tube and airline hose to burner head. Attach flare nut until nut seats against fuel tube and fitting. Tighten 1/4 turn more using 3/4" open-end wrench (100-130 inchpounds/ 11.3-14.7 n-m). 17. Replace fan (see page 19). 18. Replace fan guard and upper shell. Combustion Spark Plug Chamber Fuel Tube Flare Nut Burner Head Screw Spark Plug Wire Air Line Hose Figure 29 - Removing Burner Head, 150,000 BTU/Hr Model Nozzle Face Nozzle Burner Head Nozzle Seal Figure 30 - Removing Nozzle, 150,000 BTU/Hr Model 17 18 099606 Pump Rotor (Procedure if rotor is binding) 1. Remove upper shell (see page 10). 2. Remove filter end cover screws using 5/16" nutdriver. 3. Remove filter end cover and air filters. 4. Remove pump plate screws using 5/16" nutdriver. 5. Remove pump plate. 6. Remove rotor, insert, and blades. 7. Check for debris in pump. If debris is found, blow out with compressed air. 8. Install insert and rotor. 9. Check gap on rotor. Adjust to .003"/.004" (.076/.101 mm) if needed (see Figure 33). Note: Rotate rotor one full turn to insure the gap is .003"/.004" (.076/.101 mm) at tightest position. Adjust if needed. 10. Install blades, pump plate, air filters, and filter end cover. 11. Replace fan guard and upper shell. 12. Adjust pump pressure (see page 14). Note: If rotor is still binding, proceed as follows. 13. Perform steps 1 thru 6 above. 14. Place fine grade sandpaper (600 grit) on flat surface. Sand rotor lightly in “figure 8” motion four times (see Figure 34). 15. Reinstall insert and rotor. 16. Perform steps 10 thru 12 above. Figure 31 - Rotor Location, 30/70,000 BTU/Hr Models Sandpaper Figure 34 - Sanding Rotor .003"/.004" (.076/.101 mm) Gap Measured With Feeler Gauge Rotor Gap Adjusting Screw Gap Adjusting Screw Blade Figure 33 - Gap Adjusting Screw Locations Figure 32 - Rotor Location, 90/150,000 BTU/Hr Models 150 ROTOR PFA/P 059 Insert Blade Rotor Pump Plate Filter End Cover Air Intake Filter Air Output Filter 50 ROTOR PFA/P 056 Pump Plate Insert Rotor Blade Filter End Cover Air Intake Filter Air Output Filter Fan Guard (90,000 BTU/Hr Model Shown) Fan Guard (90,000 BTU/Hr Model Shown) Fan IMPORTANT:Remove fan from motor shaft before removing motor from heater. The weight of the motor resting on the fan could damage the fan pitch. 1. Remove upper shell (see page 10). 2. Use 1/8" allen wrench to loosen setscrew which holds fan to motor shaft. 3. Slip fan off motor shaft. 4. Clean fan using a soft cloth moistened with k...
Эта инструкция также подходит к моделям:Электрообогреватели - 70 (521.94 kb)
Электрообогреватели - 90 (521.94 kb)