Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Flame-Out Control Reset Button Figure 4 - Flame-Out Control Reset Button TO STOP HEATER CAUTION: Never unplug heater while heater is running. Heater must go through purge cycle. The purge cycle cools the combustion chamber. Damage to heater can occur if combustion chamber is not cooled. Do not restart heater until purge cycle is complete. 1. Turn thermostat dial to lowest temperature setting. This will cause heater flame to go out. The motor will continue to run during the purge cycle. This allows the fan to cool the combustion chamber. When the purge cycle is finished, the motor will stop. Do not unplug heater until purge cycle is finished. 2. Unplug extension cord from outlet. 3. To temporarily stop heater, set thermostat at a temperature lower than air around heater. Heater will cycle back on if air temperature around heater matches thermostat setting. TO RESTART HEATER CAUTION: Do not restart heater until purge cycle is finished. The purge cycle cools the combustion chamber. 1. Wait until purge cycle is finished after stopping heater. 2. Repeat steps under To Start Heater. STORING, TRANSPORTING, OR SHIPPING Note: If shipping transport companies require fuel tanks to be empty. 1. Drain all fuel from fuel filters, fuel lines, and pump (see Fuel Filters [Tank Fuel Filter], page 12). 2. Clean and flush fuel filter and canister attached to fuel pump (see Fuel Filters [Pump Fuel Filter], page 12). 3. Remove drain plug and drain fuel tank. 4. Replace drain plug. 5. If any debris is noted in old fuel, add 1 or 2 quarts of clean kerosene to tank, stir, and drain again. This will prevent excess debris from clogging filters during future use. 6. Replace fuel cap or drain plug. Properly dispose of old and dirty fuel. Check with local automotive service stations that recycle oil. 7. Add two gallons (350,000 Btu/Hr) or three gallons (600,000 Btu/Hr) of clean kerosene or No. 1 fuel oil to fuel tank. 8. Replace fuel cap. 9. Operate heater for 5 minutes (see Operation). 10. Stop heater and let cool completely. 11. Remove drain plug and drain fuel tank. 12. Replace drain plug. 13. Properly dispose of old and dirty fuel. 14. If storing, store heater in a dry location. Make sure storage place is free of dust and corrosive fumes. IMPORTANT: Do not store kerosene over summer months for use during next heating season. Using old fuel could damage heater. 099507 5 HIGH PRESSURE PORTABLE FORCED AIR HEATER 350,000 AND 600,000 BTU/HR PREVENTATIVE WARNING: Never service MAINTENANCE heater while it is plugged in, operating, or hot. Severe burns and SCHEDULE electrical shock can occur. Item How Often How To Fuel tank Filler neck screen Fuel filter assembly (Fuel tank) Fuel filter lines Fuel filter (Pump) Spark plug Fan blades and air deflectors Air passages around burner head Motor Flush every 150-200 hours of operation or as needed Check for particles in fuel when filling fuel tank. Clean when dirty Clean twice a heating season or replace as needed Check and tighten loose connections occasionally Clean fuel filter element every 250 hours Clean and regap every 300 hours of operation or replace as needed Clean each season or as needed Check each season for dirt and debris Not required, permanently lubricated See Storing, Transporting, or Shipping, page 5 Lift out of fuel tank and rinse with clean kerosene See Fuel Filters, page 12 See Fuel Lines, Page 12 See Fuel Filters, page 12 See Spark Plug, page 10 See Fan Blades and Air Deflectors, page 10 Remove debris and trash with a clean, soft cloth 6 099507 OWNER’S MANUAL TROUBLESHOOTING Note: For additional help, visit DESA International’s Technical Service web site at WARNING: Never service heater while it is plugged in, operating, or hot. Severe burns and electrical shock can occur. Only a qualified service person should service and repair heater. OBSERVED PROBLEMPOSSIBLE CAUSE REMEDY Motor does not start when heater is plugged in and thermostat setting is higher than surrounding air temperature 1. No power or low voltage at heater due to: A) Damaged power cord or extension cord B) Wrong size extension cord C) Heater plugged into outlet with voltage lower than 120 volt 2. Loose electrical connections 3. Motor overload protector tripped due to: A) Dirty fan B) Debris pulled into fan area by fan C) Binding pump D) Low voltage 4. Flame-out control not reset 5. Damaged flame-out control 6. Damaged power relay 7. Damaged thermostat 8. Binding pump 1. A) Check condition of power cord or ex tension cord. Repair or replace damaged B) Use extension cord with proper wire size (see To Start Heater, page 5) C) Make sure heater is plugged into 120 volt/60 hertz outlet 2. Check connections. Tighten if loose 3. A) See Fan Blades and Air Deflectors, page 10 B) Remove debris from fan and fan guard area C) Turn fan by hand. If fan is hard to turn, see Pump, page 11 D) See steps B and C under item 1 above Note: Be sure to reset motor overload protector by pressing reset button on top of ...
Эта инструкция также подходит к моделям:Электрообогреватели - B600D (386.5 kb)