Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
IS SUGGESTED FOR PROPER BURNING OF THIS UNIT WHEN USING WOOD. CHIMNEY MAINTENANCE Creosote and Soot - Formation and Need for Removal When wood is burned slowly, it produces tar and other organic vapors, which combine with expelled moisture to form creosote. The creosote vapors condense in the relatively cool chimney flue of a slow-burning fire. As a result, creosote residue accumulates on the flue lining. When ignited, this creosote makes an extremely hot fire. The chimney should be inspected at least twice monthly during the heating season to determine if a creosote or soot build-up has occurred. If soot or creosote has accumulated, it should be removed to reduce the risk of a chimney fire. Chimney fires burn very hot. If the chimney catches fire, immediately call the fire department, then reduce the fire by closing the inlet air control. Pour a large quantity of coarse salt, baking soda or cool ashes on top of the fire in the firebox. CAUTION A Chimney fire may cause ignition of wall studs or rafters which you thought were a safe distance from the chimney. If you have a chimney fire, have your chimney inspected by a qualified person before using again. MODEL 22AF - PARTS MODEL 22AF - PARTS •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• MODEL 22AF -PARTS LIST KEY PART NO. DESCRIPTION QTY. 1 69356 Firebox Weldment 1 2 88032 Flue Collar Gasket 1 3 40246 Flue Collar 1 4 25102R Cabinet Side 2 22682 Cabinet Back 1 6 25106R Cabinet Top 1 7 22761 Flue Collar Ring 1 8 22762 Forced Draft Ring 1 9 24959B Feed Door Hinge 1 25202B Ash Door Hinge 1 11 23800 Smoke Curtain 1 12 83445 1/4-20 x 1-1/4 Carriage Bolt 2 13 23787 Smoke Curtain Clip 2 14 83250 1/4-20 Kep Nut 2 23397 Baffle 1 16 40264 Front & Rear Liner 2 17 89066 Brick (4-1/2 x 9 x 1-1/4 THK.) 10 18 68238 Ash Pan Weldment 1 19 89319 Blower Gasket 1 22140 Junction Box Bracket 1 21 68234 Fan Limit Bracket Assembly 1 22 80145 Fan Limit Control 1 23 68231 Fan Limit Conduit Assembly 1 24 80131 4 x 4 Junction Box 1 N/S 80231 Junction Box Cover 1 68232 Blower Connection Conduit Assembly 1 26 80230 Blower Motor - 1/20 hp 1 27 40256 Grate Frame 1 28 40257 Shaker Grate 1 29 40260 Shaker Handle 1 * * 69355 Feed Door Assembly (Order ONLY if the entire Assembly is needed) 1 25105B Feed Door (Painted) 1 N/S 88066 5/8 Rope Gasket 4.58 ft 31 83872 Door Pin 2 32 89354 Feed Door Handle 1 33 83461 Handle Washer 1 34 24935 Ash Door Latch 1 83045A 3/8" SAE Flat Washer 1 36 83274 3/8-16 Lock Nut 1 37 23859B Spin Damper (Painted) 3 38 83345 3/8-16 x 1-3/4 Carriage Bolt 2 39 83178 3/8-16 Jam Nut 4 * 69388 Ash Door Assembly (Order ONLY if the entire Assembly is needed) 1 25190B Ash Door 1 N/S 88033 3/8 Rope Gasket 2.42 ft 41 89354 Ash Door Handle 1 42 ------Handle Bushings (Comes with Handle - 89354) 1 43 24935 Ash Door Latch 1 44 83045A 3/8" SAE Flat Washer 1 83274 3/8-16 Lock Nut 1 46 83503 3/8-16 x 2-1/2 Carriage Bolt 1 N/S = Not Shown APPENDIX APPENDIX INSTALLATION A NOTE: ANTI-BACKDRAFT FLAPPERS OR BAFFLE ARE REQUIRED FOR THIS INSTALLATION. •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• APPENDIX APPENDIX INSTALLATION B NOTE: ANTI-BACKDRAFT FLAPPERS OR BAFFLE ARE REQUIRED FOR THIS INSTALLATION. •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• APPENDIX APPENDIX INSTALLATION C NOTE: ANTI-BACKDRAFT FLAPPERS OR BAFFLE ARE REQUIRED FOR THIS INSTALLATION. •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• APPENDIX APPENDIX INSTALLATION D (U.S. ONLY) INSTALLATION E (U. S. ONLY) •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• APPENDIX APPENDIX INSTALLATION F INSTALLATION G •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• TROUBLE SHOOTING TIPS FOR WARM AIR FURNACE TROUBLE SHOOTING TIPS FOR WARM AIR FURNACE 1. Smoking when feed door is open. List of Problems Possible Cause a) Insufficient draft. b) Clogged chimney or chimney connector. c) Down draft in chimney. Solutions a) Open spin dampers. b) Clean chimney. c) Add raincap to chimney. 2. Furnace does not heat. a) Wood not seasoned and dry. b) Blower control set too low. c) Insufficient flue draft. a) Allow wood to season in a dry, well ventilated area for six months. b) Set blower control to higher temperature (See Page 19). c) Set flue draft (See Page 9). 3. Blower does not run. a) Improperly wired. b) Bad blower control. c) Bad relay. d) Bad blower motor. a) Wire unit properly. b) Replace blower control. c) Replace relay. d) Replace blower. 4. No air from registers - fan running. a) Registers are closed. b) Duct work improperly installed. c) Improper wiring between central furnace and Model 22AF. a) Open registers. b) Correct duct work installations. c) Wire unit properly. 5. Air from registers is not hot. a) Blower control set too low. b) Bad blower control. a) Adjust blower control to higher setting (See Page 19). b) Replace blower control. 6. Blower runs too long. Blower control cut off set too low. Set blower control cut off to higher setting (See Page 19) 7. Blower does not run long enough. a) Blower control cut off set too high. b) Bad blower motor. a) Set blower control...