Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
If a combustible mantel is installed, it must meet the clearance requirements as shown in Figure 5. 12" 10" 8" 6" 23" 21" 21/2" 19" 16" 12" Figure 5 - Mantel Clearances 5. Floor clearance: This inner chamber firebox floor must be installed at least 5" above any combustible flooring material, such as carpeting or asphalt tile, which is closer than 14" to the base of the firebox. See Figure 6. Or The inner chamber firebox floor may be installed nearer to the floor if a minimum of 14" of noncombustible material such as slate or marble is installed between the base of the firebox and the combustible flooring. See Figure 7. Can Be Less than 5" Non-Combustible Material Non-Combustible Material 5" Minimum 14" Minimum Figure 7 - Minimum Clearance above Combustible Flooring with Non-Combustible Material Installed at Base of Fireplace Figure 6 - Minimum Clearance above Combustible Flooring fireplace framing Firebox framing can be built before or after the appliance is set in place. Construct firebox framing following Figures 8 through 11 and the chart below for your specific installation requirements. See Figure 1 on Page 6 for firebox dimensions. The framing headers may rest on the top of the firebox standoffs. The firebox may be installed directly on a combustible floor or raised on a platform of an appropriate height. When the firebox is installed directly on carpeting, tile, or other combustible material, other than wood flooring, the firebox shall be installed on a metal or wood panel extending the full width and depth of the enclosure. WARNING Do not fill spaces around firebox with insulation or other materials. This could cause a fire. 205/16" 400: 401/4" 400: 661/8" 400: 2413/16" 500: 3013/16" 500: 461/4" 500: 725/8" 400: 463/4" 500: 513/8" 400: 331/16" 500: 365/16" 400: 123/4" 500: 16" 400: 2413/16" 400: 401/4"1/2" or 5/8" 203/4" 500: 3013/16" 500: 461/4" Figure 8 - Corner Installation 341/4" 400: 401/4" 500: 461/4" Figure 9 - Inside Chase Installation 400: 2413/16" 203/4" 400: 403/4"1/2" or 5/8" 500: 3013/16" 500: 463/4" Figure 10 - Stud Location Figure 11 - Recessed Installation fireplace framing The fireplace must be installed giving full consideration to the clearance and height requirements identified in this manual. WARNING 1. Bend out the nailing flanges located on each side of the firebox. 2. Slide the firebox into prepared framing or position firebox in its final position and frame later. 3. Level the firebox by checking the top edge of the firebox. Shim if necessary. 4. Anchor firebox to the side framing members using 8d nails or other suitable fasteners. See Figure 12. 5. The canopy must be installed for safe operation of the heater. See page 13 for canopy installation details. Nail Sides Through Nailing Flanges Figure 12 - Location of Nailing Flanges gas line installation Plumbing connections should only be performed by a qualified, licensed plumber. Main gas supply must be off when plumbing gas line to fireplace or performing service. WARNING Consult all local codes. All gas piping must be installed to comply with local codes, or in the absence of local codes, with the latest edition of the National Fuel Gas Code ANSI Z223.1/NFPA54. Remove the baseplate for ease of gas line installation. Remove three (3) screws along the front edge of the baseplate. Remove four (4) screws which secure the baseplate to the combustion casing (two at rear and one along each side). Replace baseplate prior to connecting gas line to heater. Consult heater installation and operating instructions for correct installation of the heater into the firebox. The 1/2" gas line may enter either from the left side or right side of the firebox. Gas access holes are provided on both sides of the firebox. A listed manual shutoff valve must be installed upstream of the appliance. A union tee and plugged 1/8" NPT pressure tapping point should be installed upstream of hte appliance. IMPORTANT: Install main gas valve (equipment shutoff valve) in an accessible location. The main gas valve is for turning on or shutting off the gas to the fireplace. A sediment trap may be upstream of the heater to prevent moisture and contaminants from passing through trap to the heater controls and burners. Failure to do so could prevent the heater from operating reliably. Consult applicable codes. An external regulator must be used on all propane / L.P.G. heaters, in addition to the regulator fitted to the heater, to reduce the supply tank pressure to 13" w.c. (maximum). Any copper tubing used to supply propane / L.P.G. from the tank must be internally tinned. Note: When connecting propane / L.P.G. vent-free room heaters, you must use pipe sealant resistant to propane / L.P.G. Important: Hold heater regulator with a wrench to prevent movement when connecting to inlet piping. Check gas type: The gas supply must be the same as stated on the heater’s rating plate. If the gas supply is different, DO NOT INSTALL THE HEATER. Contact your dealer for the correc...
Эта инструкция также подходит к моделям:Электрообогреватели - BUF500 (695.45 kb)