Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Control Flame- Reset Out Button Control Reset Button Flame-Out Figure 6 - Flame-Out Control Reset Figure 7 - Flame-Out Control Reset Button, 70,000 BTU/Hr Model Button, 100/150,000 BTU/Hr Models Continued 7 OPERATION Continued STORAGE PREVENTATIVE MAINTENANCE SCHEDULE To Stop Heater 1. Unplug power cord from outlet. To Restart Heater 1. Wait 2 minutes after stopping heater. 2. Repeat steps under To Start Heater, page 7. 1. Drain fuel tank. Note: Some models have drain plug on underside of fuel tank. If so, remove drain plug to drain all fuel. If heater does not have drain plug, drain fuel through fuel cap opening. Be sure all fuel is removed. 2. Replace drain plug if used. 3. Add one gallon (4 liters) of clean kerosene to fuel tank. 4. Attach fuel cap. 5. Move heater forwards and backwards to stir fuel. 6. Remove fuel cap or drain plug and drain fuel tank. Be sure all fuel is removed. 7. Replace fuel cap or drain plug. Properly dispose of old and dirty fuel. 8. Store heater in dry place. Make sure storage place is free of dust and corrosive fumes. IMPORTANT: Do not store kerosene over summer months for use during next heating season. Using old fuel could damage heater. WARNING Never service heater while it is plugged in, operating, or hot. Severe burns and electrical shock can occur. Item How Often How To Fuel tank Flush every 150-200 hours of operation or as needed. See Storage above. Air output and Replace every 500 hours of lint filters operation or onceSee Air Output, Air Intake, and Lint Filters, page 12. a year. Air intake filterWash and dry with soap and water every 500 hours of operation or as needed. See Air Output, Air Intake, and Lint Filters, page 12. Fuel filter Clean twice a heating season or as needed. See Fuel Filter, pages 10 and 11. Spark plug Clean and regap every 600 hours operation or replace as needed. See Spark Plug, page 11. Fan blades Clean every season or as needed. See Fan, page 15. Motor Not required/permanently lubricated 8 WARNING Never service heater while it is plugged in, operating, or hot. Severe burns and electrical shock can occur. TROUBLESHOOTING OBSERVED FAULT Heater ignites, but flame-out control shuts off heater after a short period of time Heater will not ignite, but motor runs for a short period of time. POSSIBLE CAUSE Wrong pump pressure Dirty air output, air intake, and lint filters Dirty fuel filter Dirt in nozzle Dirty photocell lens Bad flame-out control Wrong pump pressure Carbon deposits on spark plug and/or improper gap Dirty fuel filter Dirt in nozzle Water in fuel tank REMEDY See Pump Pressure Adjustment, page 12. See Air Output, Air Intake and Lint Filters, page 12. See Fuel Filter, pages 10 and 11. See Nozzle, page 13. Clean photocell lens. Replace flame-out control. See Pump Pressure Adjustment, page 12. See Spark Plug, page 11. See Fuel Filter, pages 10 and 11. See Nozzle, page 13. Drain and flush fuel tank with clean kerosene. See Storage, page 8. WARNING: High voltage! Electronic ignitor not grounded (earthed) Make sure electronic ignitor mounting is tight. Bad electronic ignitor Replace electronic ignitor. Motor does not start Flame-out control not reset Reset flame-out control when heater is button, see Figures 6 and plugged in, fan 7, page 7. rotates slowly or does not turn. Binding pump rotor If fan is hard to turn, see Pump Rotor, page 14. 9 SERVICE PROCEDURES Upper Shell Removal 1. Remove screws along each side of heater using 5/16" nut-driver. These screws attach upper and lower shells together. 2. Lift upper shell off. 3. Remove fan guard. Fuel Filter (70,000 BTU/Hr Model) 1. Remove side cover screws using 5/16" nut-driver. 2. Remove side cover. 3. Pull rubber fuel line off fuel filter neck. 4. Carefully pry bushing and fuel filter out of fuel tank. 5. Wash fuel filter with clean fuel and replace in tank. 6. Attach rubber fuel line to fuel filter neck. 7. Replace side cover. WARNING Never service heater while it is plugged in, operating, or hot. Severe burns and electrical shock can occur. Upper Shell Fan Guard Figure 8 - Upper Shell Removal, 70,000 BTU/Hr Model Upper Shell Fan Guard Figure 9 - Upper Shell Removal, 100/150,000 BTU/Hr Models Fuel Filter Side Cover Fuel Line Figure 10 - Fuel Filter Removal, 70,000 BTU/Hr Model 10 11 101585 150,000 BTU/Hr PFA/P 041.G Fuel Filter (100/150,000 BTU/Hr Models) 1. Remove side cover screws using 5/16" nut-driver. 2. Remove side cover. 3. Pull upper fuel line off fuel filter neck. 4. Carefully pry bushing, lower fuel line, and fuel filter out of fuel tank. 5. Wash fuel filter with clean fuel and replace in tank. 6. Attach upper fuel line to fuel filter neck. 7. Replace side cover. Figure 11 - Fuel Filter Removal, 100/150,000 BTU/Hr Models Fuel Filter, Bushing, and Lower Fuel Line Upper Fuel Line Side Cover Spark Plug 1. Remove upper shell (see page 10). 2. Remove fan (see page 15). 3. Remove spark plug wire from spark plug. 4. Remove spark plug from burner head using 13/16" open-end wrench. 5. Clean an...
Эта инструкция также подходит к моделям:Электрообогреватели - 70000 BTU/Hr (406.08 kb)
Электрообогреватели - 150000 BTU/Hr (406.08 kb)