Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Make sure any loose fittings, bolts, etc., are tightened before putting unit into service. 1. Before starting or servicing any generator, read and understand all instructions. Failure to follow safety precautions or instructions can cause equipment damage and/or serious MANUAL Description Unpacking General Safety personal injury. Engine instructions for these units are contained in a separate manual. Retain all manuals for future reference. 2. Never use this generator for any application other than that specified by the manufacturer. Never operate this generator under conditions not approved by the manufacturer. Never attempt to modify this generator to perform in any manner not intended by the manufacturer. 3. For maintenance and repairs, use only products and parts recommended by the manufacturer. 4. Be sure that the generator is properly grounded to an external ground path prior to operation. Refer to the section entitled Fig. 1 - Assembled Units GN301502AC and GN30C502AC “Grounding Instructions” for proper grounding procedures. 5. Be sure that the generator is operated only by persons who have read and understand these instructions. 6. Be sure that the generator is placed on a flat level surface prior to and during operation. The generator must not slide or shift during operation. 7. Keep all persons away from the generator during operation. 8. Do not allow persons wearing loose clothing or jewelry to start or operate the generator. Loose clothing or jewelry may become entangled in moving components, causing equipment damage and or personal injury. 9. Keep all persons away from parts that move or become hot during operation. 10. Be sure all powered devices are shut off prior to connecting them to the generator. 11. Keep the generator clean and well maintained at all times. ! WARNING Never operate this generator in an explosive atmosphere or poorly ventilated area. © 2000 Campbell Hausfeld / Scott Fetzer For parts, product & service information IN951300AV 2/00 visit or call 1-800-803-1436 Operating Instructions Operating Instructions 12. Be sure that all tools and appliances are in good repair and are properly grounded. Use devices that have three prong power cords. If an extension cord is used, be sure that it has three prongs for proper grounding. Do not operate this! WARNING generator on wet surfaces or in the rain. 13. Never operate the generator with damaged, broken or missing parts, or with any guarding components removed. ! DANGER Shut off the generator engine and disconnect the spark plug wire before performing any service or maintenance to the unit. 14. Use only unleaded fuel. Do not refill the fuel tank while the engine is running. Use precautions to prevent fuel spillage during refills. Be sure the fuel tank cap is securely in place before starting the engine. Allow engine to cool for at least two minutes before refueling. Never mix oil with ! CAUTION gasoline for this engine. Oil is used for engine lubrication purposes only. Assembly NO TOOLS REQUIRED FOR ASSEMBLY Fig. 2 - Handle Assembly ALWAYS OPERATE YOUR NEVER OPERATE YOUR GENERATOR UNDER THESE GENERATOR UNDER THESE CONDITIONS: CONDITIONS: 1. Rain or inclement weather 2. Excessive vibration 3. Sparking 4. Engine misfire 5. Electric output loss 6. Changing or fluctuating engine speed 7. Overheating in connected equipment 8. Damaged receptacles 9. Damaged, broken or missing parts 10. Guarding components removed Operation PRE-OPERATION 1. Check engine oil level every time you start your generator. Refer to the Engine Manual for SAE, API and fill quantity specifications. 2. Use of a Ground Fault Circuit Interrupter (GFCI) is strongly recommended. Ground Fault Circuit Interrupters can significantly reduce the possibility of injury if an electrical short occurs. A Ground Fault ! WARNING Circuit Interrupter may not be effective if used on a generator that is not grounded! 3. When installing a GFCI, be sure to follow all national and local regulations, or call a licensed or certified electrical technician. GROUNDING 1. Use the ground terminal and wing nut on the generator frame to connect the unit to a suitable ground source. Securely fasten the end terminal of the ground wire to the ground terminal on the generator frame. Tighten the washer and wing nut on top of the ground wire end terminal. 2. The ground wire should be made of #8 gauge wire. Do not use wire with 1. Read and understand these instructions 2. Clear of all persons 3. Properly grounded (generator) 4. Properly grounded (tools, appliances, etc.) 5. Flat level surfaces 6. Well ventilated areas a higher gauge number. Higher gauge numbers indicate thinner wire, which may not provide an adequate ground path. 3. The other end of the ground wire must be securely fastened to an approved ground source. The following are ground sources approved by the National Electric Code. Other ground sources may be acceptable. Refer to the National Electric Code and local regulati...
Эта инструкция также подходит к моделям:Электрогенераторы - GN30c502AC (466.21 kb)