Оценок - 5, средний балл: 3.6
(
)
)
|
Фрагмент инструкции
This feature is usually associated with extended run models. Unpacking When unpacking, inspect carefully for any damage that may have occurred during transit. Make sure any loose fittings, bolts, etc., are tightened before putting unit into service. General Safety 1. Before starting or servicing any generator, read and understand all instructions. Failure MANUAL to follow safety precautions or instructions can cause equipment damage and or serious personal injury. Engine instructions for these units are contained in a separate manual. Retain all manuals for future reference. 2. Never use this generator for any application other than that specified by the manufacturer. Never operate this generator under conditions not approved by the manufacturer. Never attempt to modify this generator to perform in any manner not intended by the manufacturer. 3. For maintenance and repairs, use only products and parts recommended by the manufacturer. 4. Be sure that the generator is properly grounded to an external ground path prior to operation. Refer to the section entitled "Grounding Instructions" for proper grounding procedures. 5. Be sure that the generator is operated only by persons who have read and understand these instructions. 6. Be sure that the generator is placed on a flat level surface prior to and during operation. The generator must not slide or shift during operation. 7. Keep all persons away from the generator during operation. 8. Do not allow persons wearing loose clothing or jewelry to start or operate the generator. Loose clothing or jewelry may become entangled in moving components, causing equipment damage and or personal injury. 9. Keep all persons away from parts that move or become hot during operation. 10. Be sure all powered devices are shut off prior to connecting them to the generator. 11. Keep the generator clean and well maintained at all times. Never operate this generator in an explosive atmosphere or poorly ventilated area. 12. Be sure that all tools and appliances are in good repair and are properly grounded. Use devices that have three prong power cords. If an extension cord is used, be sure that it has three prongs for proper grounding. Do not operate this generator on wet damaged, broken or missing parts, or with any guarding components Shut off the generator engine surfaces or in the rain. 13. Never operate the generator with removed. and disconnect the spark plug wire before performing any service or maintenance to the unit. 14. Use only unleaded fuel. Do not refill the fuel tank while the engine is running. Use precautions to prevent fuel spillage during refills. Be sure the fuel tank cap is securely in place before starting the engine. Clean up any spilled fuel before starting the engine. Allow engine to cool for at least two minutes before refueling. 15. This generator may be used for emergency stand-by service. In such cases, a manual transfer switch must be installed between the electric utilities meter and the electrical distribution box. This switch should be installed by a licensed electrician. Never mix oil with gasoline for this engine. This is a four cycle engine designed to run on pure gasoline. Oil is used for engine lubrication purposes only. Operation PRE-OPERATION 1. Check engine oil level. Oil is NOT mixed with the gasoline, however adequate oil supply is necessary for proper engine lubrication. Refer to the Engine Manual for SAE, API and fill quantity specifications. © 1996 Campbell Hausfeld IN198203AV 11/96 Operating Instructions Operating Instructions . Use of a Ground Fault Interrupter (GFI) is strongly recommended. Ground Fault Interrupters can significantly reduce the possibility of injury if an electrical short occurs. In order to install a GFI, the generator neutral wire must be internally grounded to the generator frame, and the frame must be properly grounded to the earth. A Ground Fault Interrupter may not be effective if used on a generator that is not grounded! Refer to the section entitled Grounding for proper steps to ground the generator. 3. When installing a GFI, be sure to follow all national and local regulations. If not sure of regulations or procedures, obtain assistance from a qualified (licensed or certified) electrical technician. GROUNDING 1. Use the ground terminal and wing nut on the generator frame to connect the unit to a suitable ground source. Securely fasten the end terminal of the ground wire to the ground terminal on the generator frame. Tighten the washer and wing nut on top of the ground wire end terminal. 2. The ground wire should be made of #8 gauge wire. Do not use wire with a higher gauge number. Higher gauge numbers indicate thinner wire, which may not provide an adequate ground path. 3. The other end of the ground wire must be securely fastened to an approved ground source. The following are ground sources approved by the National Electric Code. Other ground sources may be acceptable. Refer to the National Electric Code and ...