Оценок - 0, средний балл: 5
(
)
)
|
Фрагмент инструкции
DO NOT place generator where exhaust gas (A) could accumulate and enter inside or be drawn into a potentially occupied building. Ensure exhaust gas is kept away from any windows, doors, ventilation intakes, or other openings that can allow exhaust gas to collect in a confined area. Prevailing winds and air currents should be taken into consideration when positioning generator. A DANGER Using a generator indoors CAN KILL YOU IN MINUTES. Generator exhaust contains carbon monoxide. This is a poison you cannot see or smell. NEVER use inside a home or garage, EVEN IF doors and windows are open. Only use OUTSIDE and far away from windows, doors, and vents. « m 9 Assembly Controls Features and Controls Read this Operator’s Manual and safety rules before operating your generator. Compare the illustrations with your generator, to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. A - 120 Volt AC, 20 Amp, Duplex Receptacles — May be used to supply electrical power for the operation of 120 Volt AC, 20 Amp, single phase, 60 Hz electrical, lighting, appliance, tool, and motor loads. B - Circuit Breakers (AC) — Push-to-reset circuit breakers are provided to protect the generator against electrical overload. C - 120/240 Volt AC, 30 Amp Locking Receptacle — May be used to supply electrical power for the operation of 120 and/or 240 Volt AC, 30 Amp, single phase, 60 Hz electrical, lighting, appliance, tool and motor loads. D - Grounding Fastener — Consult your local agency having jurisdiction for grounding requirements in your area. E - Identification Label — Provides model, revision, and serial number of generator. Please have these readily available when calling for assistance. F - Oil Fill Cap — Check and add engine oil here. G - Oil Drain Plug — Drain engine oil here. H - Air Cleaner — Protects engine by filtering dust and debris out of intake air. J - Choke Lever — Used when starting a cold engine. K - Fuel Tank — Capacity of seven (7) U.S. gallons (26.5 L). Items Not Shown: Engine Identification — Provides model, type and code of engine. Please have these readily available if calling for assistance. Recoil Starter — Used to start the engine. Rocker Switch — Set this switch to “On” before using recoil starter. Set switch to “Off” to stop engine. 10 BRIGGSandSTRATTON.COM Cord Sets and Receptacles Use only high quality, well-insulated, grounded extension cords with the generator’s 120 Volt duplex receptacle. Inspect extension cords before each use. Check the ratings of all extension cords before you use them. Extension cord sets used should be rated for 125 Volt AC loads at 20 Amps or greater for most electrical devices. Some devices, however, may not require this type of extension cord. Check the operator’s manuals of those devices for the manufacturer’s recommendations. Keep extension cords as short as possible to minimize voltage drop. A WARNING Ml Overloaded electrical cords can overheat, arc, and burn resulting in death, bodily injury, and/or property damage._ ONLY use cords rated for your loads. Follow all safeties on electrical cords. 120/240 Volt AC, 30 Amp, Locking Receptacle Use a NEMA L14-30 plug with this receptacle. Connect a 4-wire cord set rated for 250 Volt AC loads at 30 Amps (or greater). You can use the same 4-wire cord if you plan to run a 120 Volt load. This receptacle powers 120/240 Volt AC, 60 Hz, single phase loads requiring up to 5,500 watts of power (5.5 kW) at 22.9 Amps for 240 Volts or two independent 120 Volt loads at 22.9 Amps each. The outlet is protected by push-to-reset circuit breakers. NOTICE Receptacles may be marked with rating value greater than generator output capacity._ • NEVER attempt to power a device requiring more amperage than generator or receptacle can supply. • DO NOT overload the generator. See Don't Overload Generator. 120 Volt AC, 20 Amp, Duplex Receptacles Each duplex receptacle is protected against overload by a push-to-reset circuit breaker. 60 Hz electrical loads requiring up to 2,400 watts (2.4 kW) at 20 Amps of current. Use cord sets that are rated for 125 Volt AC loads at 20 Amps (or greater). 11 Controls Operation Operation A WARNING Starting the Engine Disconnect all electrical loads from the generator. Use the following start instructions: 1. Make sure unit is on a level surface. IMPORTANT: Failure to start and operate the unit on a level surface will cause the unit not to start or shut down during operation. 2. Turn fuel valve to “On” position. Fuel valve handle should be vertical (pointing toward ground) for fuel to flow. resistance is felt. Then pull handle rapidly to overcome compression, prevent kickback, and start engine. Starter cord kickback (rapid retraction) can result in bodily injury. Kickback will pull hand and arm toward engine faster than you can let go. Broken bones, fractures, bruises, or sprains could result. When star...