Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
Compare the illustrations with your generator to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. 15 Amp Fuse — Protects the DC control circuits. Air Cleaner — Uses a dry type filter element and foam precleaner to limit the amount of dirt and dust drawn into the engine. Battery — 12 Volt DC, 33 Amp-Hour sealed battery provides power to start the engine. Battery receives trickle charge whenever generator is not running. Control Panel — Used for various test, operation and maintenance functions. See “KNOW YOUR SYSTEM CONTROL PANEL” on the next page. Engine Label — Identifies engine model and type. Exhaust Port — High-performance muffler lowers engine noise to comply with most residential codes. Oil Dip Stick — Used to check the engine oil level. Oil Drain Hose — Provided to facilitate oil changing. Oil Fill Cap — Remove to service the engine with recommended oil. Oil Filter — Filters engine oil to prolong system life. Unit Data Decal — Identifies unit by serial number. Air Cleaner Oil Filter Battery Door Opening Control Panel Door Opening Unit Data Decal Oil Service Door Opening Exhaust Port Oil Dip Stick Fuel Inlet Control Panel (see page 10) Battery Oil Drain Hose Oil Fill Cap 15 Amp Fuse Engine Label Briggs & Stratton Power Products Home Generator Owners Manual KNOW YOUR SYSTEM CONTROL PANEL Compare this Control Panel illustration with your generator to familiarize yourself with the location of these important controls: Circuit Breaker Hour Meter 15 Amp Fuse Set Exercise Switch Diagnostic LED AUTO/OFF/MANUAL Switch 15 Amp Fuse — Protects the Home Standby Generator DC control circuits. If the fuse has ‘blown’ (melted open) or was removed, the engine cannot crank or start. Replace the fuse using only an identical BUS AGC 15A fuse. AUTO/OFF/MANUAL Switch — This three-position switch is the most important control on the system and is used as follows: •“AUTO” position is the normal operating position. If a utility power outage is sensed, the system will start the generator.When utility power is restored, lets the engine stabilize internal temperatures, shuts off the generator, and waits for the next utility power outage. •“OFF” position turns off running generator, prevents unit from starting and resets any detected faults. •“MANUAL” position starts the engine after a short amount of time. It is used for maintenance or diagnostic functions. Circuit Breaker — Protects the system from shorts and other over-current conditions. Must be ON to supply power to the Automatic Transfer Switch. Diagnostic LED — Used for troubleshooting operational problems with the Home Standby Generator.All fault conditions are described in the section “Fault Detection System”. Hour Meter — The hour meter records the total number of hours the generator has been running and is used to schedule maintenance tasks. Set Exercise Switch — Used to set the exercise cycle start time and day-of-the-week. Exercise cycle only occurs in AUTO mode. 10 Briggs & Stratton Power Products Home Generator Owners Manual Access Doors The Home Standby Generator is equipped with an enclosure that has four access doors (Figure 3).The doors are named for a significant component located behind them. Starting with the side that has the fuel connection and proceeding clockwise, the doors are named: • Oil Service door • Air Intake door • Control Panel door • Battery door Each Home Standby Generator is equipped with three identical keys.These keys fit the locks that secure the Oil Service and Control Panel doors. CAUTION DO NOT operate the Home Standby Generator unless the Oil Service and/or Control Panel doors are installed. • Failure to install Oil Service and/or Control Panel doors while operating the Home Standby Generator will cause overheating. To Remove an Access Door: 1. Insert key into lock of access door you wish to remove and turn one quarter turn clockwise. NOTE: The key is retained in the lock when the locks are open. 2. Grasp door’s lift handle and pull door upwards until security pins are free of lower base. 3. With security pins free, pull lift handle outward (away) from unit while pulling door down and out of upper door channel.The door will come free of generator enclosure. The Battery door does not have a lock and the Air Intake door does not have a lock or lift handle.The Air Intake door is opened by lifting on the louvers instead of a lift handle. However, you must remove the door lock screws, found directly above the center of the doors. WARNING Running engines produce heat.Temperature of exhaust port and nearby areas can reach or exceed 600°F (316°C). Severe burns can occur on contact. • DO NOT touch hot surfaces. • Allow equipment to cool before touching. To Install an Access Door: 1. Support door by grasping lift handle or louver. Guide top of door into generator enclosure. 2. Lift door up into its upper channel until security pins clear sill of enclosure. 3. Push lower half of ...
Эта инструкция также подходит к моделям:Электрогенераторы - 01815-0 (2.09 mb)