Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
Slide the cover down until it locks. Black wire to Ground (-) terminal Red wire to Positive (+) terminal APC, Back-UPS, and PowerChute plus are registered trademarks of American Power Conversion. All other trademarks are property of their respective owners. Back-UPS does not power computer/monitor/external drive during an outage Internal battery is not connected. Computer, monitor or external disk/ CD-ROM drive is plugged into a Surge Only outlet. Check the battery connections. (See “Connect the Battery” under “Installation” on the front page of this document. Move computer, monitor, or external drive power cord plug to the Battery Backup outlets. Back-UPS operates on battery although normal utility voltage exists Back-UPS circuit breaker “tripped”. The wall outlet that the Back-UPS is connected to does not supply utility power to the unit. Disconnect non-essential equipment from the Back-UPS. Reset the circuit breaker (located on the rear panel of the Back-UPS) by pushing the circuit breaker button fully inward until it catches. Back-UPS does not provide expected backup time Back-UPS is excessively loaded. Back-UPS battery is weak due to recent outage and has not had time to recharge. Battery requires replacement. Unplug non-essential Battery Backup connected equipment, such as printers and plug them into Surge Only outlets. Note: Devices that have motors or dimmer switches (laser printers, heaters, fans, lamps, and vacuum cleaners, for example) should not be connected to the Battery Backup outlets. Charge the battery. The battery charges whenever the Back-UPS is connected to a wall outlet. Typically, eight hours of charging time are needed to fully charge the battery from total discharge. Back-UPS run-time is reduced until the battery is fully charged. Replace battery (see Order Replacement Battery). Batteries typically last 3-6 years, shorter if subjected to frequent power outages or elevated temperatures. A red indicator is lit Battery is not connected properly. The Overload indicator is lit if equipment connected to the Battery Backup outlets is drawing more power than the Back-UPS can provide. Battery requires replacement. Check the battery connections. Consult "Connect the Battery" under "Installation" on the front page of this document. It shows how to access the battery and connect the wires. Move one or more equipment power plugs to the Surge Only outlets. The battery should be replaced within two weeks (see "Order Replacement Battery"). Failure to replace the battery will result in reduced run-time during a power outage. Connect the Back-UPS to another wall outlet or have a qualified electrician check the building wiring. Red indicators are flashing Back-UPS failure. Call APC for service. Service 1. Consult the Troubleshooting section to eliminate common problems. 2. Determine if the circuit breaker is tripped. If the circuit breaker is tripped, reset the breaker and determine if the problem still exists. 3. If the problem persists, consult the APC Worldwide Web site (or call customer service. • Record the model number of the UPS, the serial number, and the date purchased. Be prepared to troubleshoot the problem over the telephone with a technician. If this is not successful, the technician will issue a Return Merchandise Authorization Number (RMA#) and a shipping address. • If the UPS is under warranty, repairs are free. If not, there is a repair charge. 4. Pack the UPS in its original packaging. If the original packing is not available, ask customer service about obtaining a new set. Pack the UPS properly to avoid damage in transit. 5. Write the RMA# on the outside of the package. 6. Return the UPS by insured, prepaid carrier to the address provided by customer service. Note: If the UPS requires service, do not return it to the dealer. The following steps should be taken: Note: Never use StyrofoamTM beads for packaging. Damage sustained in transit is not covered under warranty (insuring the package for full value is recommended). Warranty The standard warranty is two (2) years from the date of purchase. APC’s standard procedure is to replace the original unit with a factory reconditioned unit. Customers who must have the original unit back due to assigned asset tags and set depreciation schedules must declare such a need at first contact with an APC Technical Support representative. APC will ship the replacement unit once the defective unit has been received by the repair department, or cross ship upon the receipt of a valid credit card number. The customer pays for shipping the unit to APC. APC pays ground freight transportation costs to ship the replacement to the customer. APC Contact Information Replace Battery indicator lit and an alarm sounds when the Back-UPS is turned on Internal battery not connected. Check the battery connections. Copyright © 2000 American Power Conversion. All rights reserved. USA/Canada Mexico Brazil Worldwide Internet Technical Support 1.800.800.4272 ...
Эта инструкция также подходит к моделям:Электрогенераторы - CS 350 (393.31 kb)