Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
Incorrect reassembly may result in a risk of electric shock or fire. 13. The batteries in this clipper have been designed to provide maximum trouble-free life. However, like all batteries, they will eventually wear out. Do not disassemble battery pack and attempt to replace the batteries. 14. To preserve natural resources, please recycle or dispose of expired battery pack properly. This product contains a nickel-cadmium battery. They must be disposed of properly. Local, state, or federal laws may prohibit disposal of nickel-cadmium batteries in ordinary trash. Consult your local waste authority or call 1-800-822-8837 for information regarding available recycling and/or disposal options. 15. Battery pack removal and preparation for recycling: WARNING: Upon removal, cover the battery pack’s terminals with heavy duty adhesive tape. Do not attempt to destroy or disassemble battery pack or remove any of its components. Nickel-cadmium batteries must be recycled or disposed of properly. Also, never touch both terminals with metal objects and/or body parts as short circuit may result. Keep away from children. Failure to comply with these warnings could result in fire and/or serious injury. SAVE THESE INSTRUCTIONS THIS PRODUCT IS INTENDED FOR COMMERCIAL USE Model BGRC Cord Pack Use 1. Models BGRC/BGR+ will run on an average of 3800 SPM with the cord pack attached. 2. Models BGRC/BGR+ can be used with either the cord pack or the battery. 3. Remove the transformer wall plug and clipper from the carton. 4. With the clipper in the off position, insert the adapter plug into the bottom of the clipper. Note that the adapter plug is fitted with a tongue to align properly with the groove in the clipper. Once the adapter plug and clipper are aligned, press firmly together. You may hear a click as the adapter plug contacts engage. 5. Plug the transformer wall plug into the AC outlet as identified on the carton. 6. The clipper is now ready to be used. See page 6 for clipper use Tongue Adapter Plug Transformer Wall Plug Model BGR+ With Battery Use 1. Models BGRC/BGR+ will run on an average of 3800 SPM with the battery pack attached. 2. Models BGRC/BGR+ can be used with either the cord pack or the battery. READ THE FOLLOWING BEFORE CHARGING THIS CLIPPER 1. Remove the charger from the carton and plug into an AC outlet as identified on charger unit and on carton. 2. Place the Andis Model BGR+ Cordless Clipper in the form fitting pocket in the charger base. Note that the battery pack is fitted with a slot to align properly with the charger. Once the battery and charger are aligned, press the battery pack firmly into the charger until it rests at the bottom of the pocket. You may hear a click as the charging contacts engage this is nor- Diagram A mal. The battery pack may be charged while on the clipper, or separately. Push the battery release button (Diagram B) on the clipper, and pull straight out to remove the battery. NOTE: The battery pack is designed to run the clipper for about one hour. A clean, sharp, well-oiled blade will provide the best run time. 3. Before initial use battery pack must be charged for a minimum of one hour. 4. The charger base has two indicator lights: Below is a description of the Sensacharge light sequences: (Diagram C) Continuous Green Light (Fast Charge)- Charger will fully charge battery pack in less than one hour. Rapid Green Blinking Light (Charging Complete)- Battery pack is fully charged. Long Green Blinking Light (“Refresh”) Charger is draining battery pack in preparation for fast charge. Please reference the section “Use of the Refresh Feature” on page 6 for an explanation. Short Green Blinking Light- a) With Continuous Red Light (Charge Standby)- Battery pack is trickle charging because it is either too hot or too cold to accept a fast charge. Fast charging will occur once battery pack temperature moderates. b) Without Red Light (Charge Preparation)-Battery pack is undergoing trickle charge, because it has been drained excessively during use. 5. The clipper can be left in the charger base for an indefinite period of time. The charger will supply only what is needed and will not damage the battery due to overcharge. Diagram B Diagram C SAFETY RULES FOR CHARGER AND BATTERY PACK 1. Clipper motor switch must be in the “OFF” position for the charger to operate properly. Do not return the clipper to the charger base with the motor switch in the “ON” position. If the clipper is accidentally put on the charger base in the “ON” position, remove it promptly. Turn clipper off and return to the charger base. 2. Do not insert anything metallic into the battery pocket of the charger base (Diagram D). 3. Do not allow the ventilation slots on the charger base to become blocked or filled with foreign material. Avoid subjecting the charger to excessively dirty locations. If the slots become clogged with dust or hair, unplug charger and gently remove hair with a soft brush or a vacuum cleaner (Diagram E). 4. Do n...