Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Place the Jet Clean System on a flat, level surface. 1 2 3 4 Lift the transparent cleaning reservoir from the Jet Clean System. Turn the reservoir cap counterclockwise (1) and remove from the cleaning reservoir (2) . Unscrew the lid on the Jet Clean Solution bottle (Model HQ200) provided with the razor. Remove the airtight seal by lifting up the tabs on the seal. Replace lid on the bottle making sure the lid is screwed on securely. 5 Open lid and pour the Jet Clean Solution into the transparent cleaning reservoir. The reservoir can be completely filled with one (1) bottle of the Jet Clean Solution (Model HQ200). Discard cleaning solution bottle after contents have been poured into the reservoir. NOTE: ONLY USE PHILIPS NORELCO JET CLEAN SOLUTION (MODEL HQ200) WITH THE JET CLEAN SYSTEM. ANY OTHER SOLUTION MAY CAUSE DAMAGE TO YOUR RAZOR. 26 ENGLISH C C C 6 The amount of cleaning solution in the transparent cleaning reservoir is visible on both sides of the Jet Clean System. When the level gets low, refill with Philips Norelco HQ200 Cleaning Solution. . The cleaning solution is automatically supplied from the reservoir to the cleaning canister through a special mechanism in the reservoir cap. 7 Replace cap on reservoir (2) and turn clockwise (1) making sure cap is screwed on securely. . The cleaning solution may foam if the reservoir level is too low. Discard remaining solution, rinse the reservoir with warm water from the tap and refill with new cleaning solution. . If you clean your razor every day, you should refill the reservoir approximately once a month. 8 Carefully lower the cleaning reservoir back into the Jet Clean System making sure the reservoir is properly aligned with the base unit. C C C ENGLISH 27 Jet Cleaning the Razor . If the razor does not contain enough power for one (1) shave, the Jet Clean Cleaning System may not work properly. Charge the razor in the Jet Clean System before using the it to clean your razor. 1 Connect the small plug to the Jet Clean System. Connect the charging plug into any 100V to 240V AC outlet. Use only the charging plug provided. The razor holder automatically moves up to the highest position. 2. Place the Jet Clean System on a flat, level surface. Fill the cleaning reservoir with cleaning solution (see ‘Preparing Jet Clean System For Use’). 3 4 Remove protective razor head cap from razor. Place the razor head side down in the razor holder so that the razor head fits into the configuration shown inside the Jet Clean System. Gently press the base of the razor towards the back of the Jet Clean System so that the razor base fits snugly in place. Lock the razor into place by pushing the lever down completely. The charging light will blink to indicate the razor automatically begins to charge. 28 ENGLISH C 5 Press the ON/OFF button to start the cleaning cycle. The cleaning light on the Jet Clean System star ts blinking and the razor is automatically lowered into the cleaning solution. The razor stops charging while it is cleaning. . During the first few minutes of the cleaning cycle, the razor will automatically turn on and off several times while the razor holder lowers and raises the razor’s position in the cleaning solution, removing all debris. . After approximately 5 minutes, the razor holder will be raised slightly and will stay in this position for about 55 minutes. The cleaning light will remain blinking until the entire process is complete. . Do not lift the razor lever or press the ON/OFF button while the cleaning cycle is running. If this does occur, the cleaning cycle will stop and the razor holder will automatically move to the highest position. The cleaning cycle can be re-started by pressing the ON/OFF button once. . If the power plug is disconnected before the cleaning cycle is complete, the razor holder will remain in its current position. Reconnect the plug into the outlet or Jet Clean System and the razor holder will automatically move to the highest position. The cleaning cycle can be re-started by pressing the ON/OFF button once. C C ENGLISH 29 6 When the entire cleaning cycle is complete and the razor is hygienically clean, the razor will be raised to the highest position and the cleaning light on the Jet Clean System will light up continuously. 7 Raise the lever holding the razor to the highest position (1) and carefully remove the razor from the Jet Clean System (2). . You may quickly rinse the razor heads with warm water after using the Jet Clean System to remove any residual cleaning solution. . If the razor needs to be recharged, you can simply leave it in the Jet Clean System after cleaning and the razor will automatically recharge. The charging light on the Jet Clean System will blink to indicate the razor is recharging. . For optimal razor drying time after cleaning, remove razor from Jet Clean System after the cleaning cycle is complete and allow to air dry. . You may store your razor in the Jet Clean System. Unplug from the outlet when chargi...