Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
. Always switch Razor OFF, unplug and remove power cord before cleaning. . Never clean, remove or replace head assembly while motor is on. . Do not apply pressure to combs. Do not touch razor heads with hard objects as this C 8170XLDFU-01_31_05Norelco.qxd 2/11/05 3:56 PM Page 17 (Zwart plate) ENGLISH 17 may dent or damage precision-made slotted combs. . Do not use razor if combs are damaged or broken. Facial injury may occur. . Unplug the charging stand. The charging stand may be wiped clean using a damp cloth. 1 The light above faucet symbol will start blinking after each shave to remind you that the razor needs to be cleaned (except when the bottom light burns red). Quick Cleaning: Razor Heads The quickest and easiest way to clean the razor heads and hair chamber is to rinse them after each use or at least once a week with hot water: Water from the tap should be on a hot setting, BUT BE CAREFUL TO TEST WATER FIRST SO AS NOT TO BURN OR SCALD HANDS. . Regular cleaning guarantees better shaving results. . You may also quickly rinse your razor heads after each use. . Do not immerse razor in water. C . While rinsing razor heads, water may drip out of the base of razor.This is a normal occurrence. 1 Always turn razor OFF, unplug from outlet and remove cord from razor or charging stand (model 8170XLCC only) before cleaning. 8170XLDFU-01_31_05Norelco.qxd 2/11/05 3:56 PM Page 18 (Zwart plate) 18 ENGLISH C C C C 2 Press the Razor Head Release Button, flip open the Razor Head Assembly. 3 Clean inside razor heads and hair chamber by running under hot water. 4 Clean outside of Razor Head Assembly by running under hot water. 5 6 Close the Razor Head Assembly and shake off excess water. Open Razor Head assembly again and leave open to air dry. NOTE: Do not wipe or dry the shaving heads with a towel or tissue.This could damage the shaving heads. 7 You may also clean the hair chamber without water by using the supplied brush. 8170XLDFU-01_31_05Norelco.qxd 2/11/05 3:56 PM Page 19 (Zwart plate) C C C ENGLISH 19 Jet Cleaning: Model 8170XLCC . See separate Jet Clean & Charge instruction book for complete charging and cleaning instructions. Once A Month: Razor Heads Do not mix up the cutters and combs as the shaving performance may be adversely affected for several weeks before optimal shaving performance is restored. 1 Turn razor OFF, remove the charging plug from the outlet and cord from the razor or charging stand (model 8170XLCC only). 2 Press the razor head release button to open the razor head assembly. 3 Turn the wheel counterclockwise (1) and remove the retaining frame (2). 4 Remove and clean one set of cutters and combs at a time. 8170XLDFU-01_31_05Norelco.qxd 2/11/05 3:56 PM Page 20 (Zwart plate) 20 ENGLISH C C C 5 Separate the cutter from the comb and rinse clean under hot water. Do not clean more than one cutter and comb at a time, since they are all matching sets. If you accidentally interchange the cutters and combs, it could take several weeks before optimal shaving performance is restored. 6 Replace the set back into the Razor Head Assembly so that the ‘wings’ on the comb fit within the brackets located towards the center of the Assembly. The set will only fit into the Razor Head Assembly if the ‘wings’ are between the brackets. Make sure that the two pointy edges of the head fit exactly into the recesses. 7 8 9 Repeat the process for the other two sets of cutters and combs. Replace the frame. Press down (1) and turn wheel clockwise (2) until it locks into place. 10 Close the Razor Head Assembly. 8170XLDFU-01_31_05Norelco.qxd 2/11/05 3:56 PM Page 21 (Zwart plate) C C ENGLISH 21 Once A Month: Razor Heads For optimum performance, razor cutters and combs should be cleaned in a degreasing liquid (e.g. Norelco Razor Cleaner, model RC1776, or rubbing alcohol) and lubricated with Norelco Razor Lubricant, model AL80, or one drop of mineral oil (in the center of the head). This helps prevent wear of the shaving heads. After Each Use: Trimmer Turn razor OFF. Push down spring-release trimmer switch. Clean trimmer with the brush every time you use it. 4 Lubricate the trimmer teeth with Norelco Razor Lubricant (model AL80) or with one drop of mineral oil every 6 months. 5 Close trimmer by pressing trimmer down. 1 2 3 This razor has no other user-serviceable parts. Any other service should be performed by an Authorized Service Location. 8170XLDFU-01_31_05Norelco.qxd 2/11/05 3:56 PM Page 22 (Zwart plate) 22 ENGLISH Storage C . Model 8170XLCC only:The razor can be placed in the charging stand for safe storage. If storing razor in stand, remove the plug from outlet. . Be sure razor is turned off. Remove cord from outlet and razor or charging stand (Model 8170XLCC) before storing in a safe, dry location where it will not be crushed, banged, or subject to damage. . Do not wrap cord around razor or charging stand (Model 8170XLCC) when storing. . Store cord in a safe location where it will not be cut or damaged. . Do not place or s...