Оценок - 5, средний балл: 4.4
(
)
)
|
Фрагмент инструкции
Removing the carrying holder Remove the carrying holder while pressing down on both sides. Charge Charging the shaver Perform the following steps to charge the shaver if it seems to lose speed. You can charge the shaver with the carrying holder attached. 11Turn off the shaver and insert it in the AC adaptor until it clicks as illustrated. •Wipe off any water droplets on the side terminals. •If you charge the shaver with the power switch turned on, it will start working when you remove the shaver from the AC adaptor. 1222Put the plug into a household outlet. The charge indicator lamp glows red. •Charging is completed after approx. 15 hours. •When charging the shaver for the first time, or when it has not been in use for more than 6 months, the charge indicator lamp may not glow for a few minutes, or the operating time may shorten. Please charge it for more than 23 hours in such cases. • If the shape of the plug does not fit the power outlet, use an attachment plug adaptor with proper configuration. 3 33 Disconnect the plug after charging is complete. • Charging the battery for more than 15 hours will not affect battery performance. • Recommended ambient temperature for charging is 0 .35 °C (32 .95 °F). The battery may not charge under extreme low or high temperatures. English • The charge indicator lamp glows and stays on until the plug is disconnected from a household outlet. • A full charge will supply enough power for approx. 7 shaves of 3 minutes each. (This will differ depending on usage.) You cannot operate the shaver while charging. Shave Using the shaver Press the power Hold the shaver as 1 112 22 switch. illustrated above and shave. Caution • Before shaving, check that the cleaning shutter is closed. • Do not place your fingers on the power switch while using the shaver. This may cause the shaver to turn off. • Do not use shaving creams or face cleansers containing scrubbing compounds as these may cause the outer foil to clog. Using the trimmer Slide the trimmer handle up. Place at a right angle to your skin and move downwards to trim your sideburns. • We recommend using the shaver in an ambient temperature range of 0 .35 °C (32 .95 °F). If used outside this range, the appliance may stop operating. Clean Cleaning the shaver Start shaving by applying gentle pressure to your face. Stretch your skin with your free hand and move the shaver back and forth in the direction of your beard.You may gently increase the amount of pressure as your skin becomes accustomed to this shaver. Applying excessive pressure does not provide a closer shave. 1. Remove the shaver from the AC adaptor. 2. Apply some hand soap and some water to the outer foil. •Close the cleaning shutter. 3. Turn the shaver on. 3 You can also use a pen grip to hold the shaver. 7 English Replacing the system outer foil and the inner blades system outer foil once every year inner blades once every two years Removing the outer foil section Press the foil frame release button and lift the outer foil section upwards. Attaching the outer foil section After turning the water inlet surface to the front, securely attach the outer foil section to the shaver until it clicks. 1 2 >>Replacing the system outer foil 1. Press the system outer foil release buttons and pull down the system outer foil. 2. Align the water inlet surface and the system outer foil mark ( ) and securely attach together. ••The system outer foil cannot be reversely attached. ••Always insert the system outer foil to the foil frame when attaching to the shaver. >>Replacing the inner blades 1. Remove the inner blades one at a time. ••Do not touch the edges (metal parts) of the inner blades to prevent injury to your hand. 2. Insert the inner blades one at a time until they click. Ў Ў To remove light dirt For heavy dirt 4. Slide the cleaning shutter until it clicks. 5. Clean the outer foil section with running water. 6. Turn the shaver off. ••Rinse with water and shake up and down several times to remove the water. 4. Turn the shaver off after 10 - 20 seconds. 5. Remove the outer foil section and turn the shaver on. 6. Clean the shaver and the outer foil section with running water. ••Rinse with water and shake up and down several times to remove the water. Ў Ў 7. Wipe off any drops of water with a dry cloth. 8. Dry the outer foil section and the shaver completely in a shaded area. 9. Attach the outer foil section to the shaver. ••Open the cleaning shutter. ••The outer foil section will dry faster if removed from the main body. 8 English > Replacement parts Replacement parts are available at your dealer or Service Center. Replacement parts for ES.SL41 System outer foil and inner blades WES9013 System outer foil WES9087 Inner blades WES9068 . . . . . . . . . . . Removing the built.in rechargeable battery ATTENTION: A nickel metal hydride battery that is recyclable powers the product you have purchased. Please call 1.800.8.BATTERY for information on how to recycle this battery. Remove the built...