Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
It will adjust automatically to voltages between 100-240V AC. In some areas, a special plug adaptor may be required. The charge (status) lamp will glow when the shaver is being charged. It will flash when the charging is completed. A full charge will supply enough power for approx. 14 shaves (3 minutes per shave for a normal beard). (For ES8017/ES8018/ES8019, see fig. 2) You should charge the shaver for 1 hour if the battery capacity lamp blinks red. The battery capacity lamp will glow in three colors depending on its charge capacity level: 100% - 30% : green 30% - 10% : orange less than 10% : blinking in red (For ES8016, see fig. 3) You should charge the shaver for 1 hour if the low battery indicator glows. Cord shaving Connect the shaver to the AC outlet and turn the shaver on. If the shaver does not run, charge it for approx. 1 minute. Using your shaver Caution – The system outer foil is very thin and can be damaged if handled improperly. Before each use, always check the foil for damage. To avoid personal injury, do not use if the foil or other parts of the shaving head is damaged. Push the On/Off switch to turn the shaver on. Hold the shaver at a right angle (90°) to your skin (see fig. 4). Start out shaving by applying gentle pressure to your face. Stretch your skin with your free hand and move the shaver back and forth in the di- 7 10 g h i f e d j b c a rection of y our beard. Y ou ma y gently incyrease the amount of presure as our skin becomes acustomed to this sha v er . Applying e xcessiv e pressure does not pro vide a closer sha v e . System outer foil (see fig. 5) System outer foil has a slit blade (a) between 2 foils (b). They move up and down independently to follow the contours of your face. The slit blade catches and cuts longer and lying hairs easily. Using the trimmer (see fig. 6) Slide the trimmer handle up to open the trimmer. Place the trimmer at a right angle to your skin and move it downward to trim sideburns. Cleaning your shaver (see fig. 7) Warning – To prevent electric shock or personal injury, disconnect the power cord from the shaver and turn the shaver off before cleaning. For cleanliness and convenience, we recommend that you clean your shaver with water and a liquid hand soap. Regular cleaning will keep your shaver in good condition while odors or bacteria from developing, and maintain performance. With the system in place, apply some foil. 8 Turn the shaver on and pour some water over the outer foil. After about 10-20 seconds, turn the shaver off. Remove the foil frame and clean it with running water. Wipe off any moisture from the shaver with a dry cloth and remove the protective cap to allow the system outer foil to dry completely. Replacing shaving head components It is recommended that you replace the system outer foil at least once a year and the inner blade at least once every 2 years to maintain your shaver’s cutting performance. Replacing the system outer foil (see fig. 8) Squeeze the system outer foil release buttons and lift the system outer foil upward to remove it. To insert the new system outer foil, press down until it snaps into place. Replacing the inner blades (see fig. 9) Squeeze the foil frame release buttons and lift the foil frame upward to remove it. Remove the inner blade, one at a time, by grasping them firmly at both ends and pulling straight away from the shaver. To insert the new inner blade, hold the blade, one at a time, at both ends and press downward until it snaps into shaver. ATTENTION: 2 nickel metal hydride batteries that are recyclable power the product you have purchased. Please call 1-800-8-BATTERY for information on how to recycle the batteries. How to remove the built-in rechargeable batteries before disposal of the shaver (see fig. 10) The batteries in this shaver are not intended to be replaced by consumers. However, the batteries may be replaced at an authorized service center. The procedure described below is intended only for removal of the rechargeable batteries for the purpose of proper disposal. Always make sure that the batteries have been removed from the shaver before disposing of it. 1. Disconnect the power cord from the AC outlet, and remove the power cord from the shaver. 2. Remove the outer foil frame and the inner blades. 3. Remove the trimmer driving bar (a), slit blade driving bar (b) and two screws (c). 4. Remove the four screw covers (d) (using something a toothpick), four screws (e), and the panel cover (f). 5. Remove the screw (g) and the bottom cover (h). 6. Remove the back panel (i). 7. Remove the batteries from the battery block (j). WARNING: Do not attempt to replace the battery for the purpose of reusing the shaver. This could result in the risk of fire or electric shock. Caution – To prevent personal injury or damage to the product, • Do not charge the shaver where the temperature is below 0° C (32° F) or above 40° C (104° F), where it will be exposed to direct sunlight or a heat source, or where there is a...