Оценок - 5, средний балл: 4
(
)
)
|
Фрагмент инструкции
If you want hair to be even shorter: A) Apply more pressure to the head with the attachment comb that is in place. This takes a little practice, of course. OR B) Just switch to a shorter attachment comb. Remember, it’s better to leave too much hair than too little. For longer hair on top, use the barber comb and lift hair on the top of the head, cutting over the comb. Or hold the hair between the fingers and cut to desired length. Always working from the front to the back of the head; gradually cut the hair shorter by reducing the space between the comb or fingers and the head. Comb often to check for uneven strands, and to get rid of trimmed hair. OUTLINING: Outlining requires no attachments. Comb hair into the desired style. Position the clipper between the sideburns and the ear (see below), making sure the corner edge of the blade is against the hairline. With the outline of the hair as your guide, slowly move the clipper over, around and behind the ears. For the back of the neck and the sideburns, hold the clipper upside down (see above) and, holding it against the skin at the length desired, move the clipper downward. STOP. COMB. CHECK. For best results, do as the professionals do: comb hair often, and check clipping results as you comb. This way you avoid uneven sides, bangs, neckline, etc. SHORT CUTS TO PERFECT FLAT TOPS, CREW CUTS, ETC. Always cut from the back of the neck to the crown, using the longest comb setting. Hold the comb attachment flat against the head and slowly move the clipper up through the hair. Use the same technique for the sides, cutting from the bottom to the upper side of the head. For the front to the crown, cut the hair against the direction in which it grows. Then even it up with the sides. For a flat top, use the flat comb, not the attachment comb. Just cut hair on top of the head over the flat comb. (see above). To taper hair down to the neckline, use attachment comb #1. Comb hair and check for uneven spots. Outline sideburns and neck areas (see “Outlining”). USER-MAINTENANCE INSTRUCTIONS CARE OF YOUR CLIPPERS IF YOU DETERMINE THAT BLADE ALIGNMENT IS INCORRECT: Maintenance of the Blade Always apply oil to the blades before, during and after use. This will ensure maximum cutting performance. Hold clipper away from your body in a downward position and apply oil on the front and sides of the cutter blade. Wipe excess oil off with a soft dry cloth. Keep oil away from children. Conair® hair clippers are carefully inspected to insure that the blades are in perfect alignment. You will need to realign the blades after removing them for cleaning or replacement, or if they should be knocked out of alignment. How can you tell if the blades need realigning? Simply match them up, point for point, to conform with the drawing below. To replace cutting comb and cutter after removal for cleaning, replacement or, because they are out of alignment, slide the cutter back onto the black plastic oscillating head. Next, you must make sure that the cutter (small blade) and the cutting comb (large blade) are properly aligned. Line up the new or existing cutting comb with the two screw holes. Place the original screws, one in each hole, and lightly tighten with a Phillips head screwdriver. *The top edge of the cutting comb should be 1/32” to 1/16” (.79 mm. to 1.59 mm.) higher than the top edge of the cutter. This is important so that the clipper does not cut too close, or come in contact with the skin. *The extreme left-hand tooth of the cutting comb must cover or be to the extreme left hand of the first small tooth of the cutter. *Be sure that the extreme right hand big tooth of the cutter touches the extreme right hand tooth of the cutting comb. Any other servicing should be performed by an authorized service representative because this appliance has no user serviceable parts. The product is for household use. Do not pull, twist, or wrap line cord around appliance. SPECIAL OIL To maintain the blades of your Conair® clipper in peak condition, oil them after every three or four haircuts. Gently place a few drops of oil on the teeth of the blades, using the special Conair oil included with your set. Turn the clipper on for a minute, then turn off. This light, natural oil was formulated specifically for the Conair® high-speed clipper. Because it is the right oil to use, it will not slow down the blades. Never use any other product; there is no substitute for Conair oil. Keep oil away from children. 4. First, comb hair until it’s tangle-free. Then hold clipper in a comfortable grip. Now you’re ready to cut. MEDIUM TO LONG CUT To begin with, cut only a small amount of hair until you become used to the length each attachment leaves the hair. Try the longest attachment on the clipper first. If you want a shorter cut, you can then use shorter combs. • Short attachment comb (number 1) cuts hair to 1/8" (3.175mm). • Medium-Short attachment comb (number 2) cuts hair to 1/4" (6.350mm). • Medium-Long attachmen...