Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
Wash and dry your skin thoroughly prior to shaving. In order to achieve the closest shave and avoid unnecessary wear on the foils, be sure that both foils contact the skin simultaneously. Do not hold the shaver at an angle where only one foil contacts the skin – this will cause distortion of the foil and may result in skin irritation. Stretch your skin with your free hand while using short, circular strokes. This will make the hairs stand out from your face and allow the cutting heads to reach them more easily. Shave against the grain for optimum results. To facilitate cutting and avoid foil wear, do not apply the shaver to your skin with high pressure. The normal replacement period for the foil screens is about 6 months. Axis Nitris and Axis Fuel |12| english In order to maintain shaving performance and comfort, replace the cutters at least once a year. To order replacement parts, please refer to the “Ordering Replacement Parts” section of this manual. Using this Shaver 1. Remove the protective plastic headguard. (Fig. 1) 2. Ensure that the foil screens and inner cutters are not damaged. Replace damaged parts before using. To obtain replacement parts, refer to the “Ordering Replacement Parts” section of this manual. 3. To turn the shaver on, depress the lock button and slide the on/off switch up to the “on” position. (fig. 2) Axis Nitris and Axis Fuel |13| english fig.11 2 .4. Gently stretch the skin of your face with your free hand while moving the shaver slowly and smoothly against the grain of your beard. Hold the shaver at a 90° angle to your face while maintaining contact with the foils. 5. To shave the chin area, gently pull the skin upward and stroke the shaver in an easy up and down motion. To avoid damaging the delicate foils, do not apply high pressure. 6. Turn shaver off and replace protective headguard. To Shave Longer Hairs, Sideburns or Beards The trimmer easily cuts the longer, hard to reach hairs of the face and neck. 1. Turn the shaver on. 2. Push up the trimmer switch button into its locked position. Axis Nitris and Axis Fuel |1 | english 3. To trim sideburns, hold so that the trimmer lightly touches the skin at a 90° angle and move downwards. To avoid draining the battery, keep the trimmer in its off position when not in use. To shave mustaches 1. Turn the shaver on. 2. Slide the on/off switch up to the “FINE” position. 3. Place the adjustable foil in gentle contact with your skin. Move the shaver slowly while gently stretching your skin. Axis Nitris and Axis Fuel |1 | english Cleaning the Head and Cutter Assembly Regular cleaning is necessary to maintain the optimal performance and maximum comfort from the shaver. Wipe the shaver’s body using a damp cloth and mild soap or detergent. To avoid damaging the shaver, do not use harsh cleansers or solvents. Wet Cleaning 1. Switch the shaver off and ensure that the power cord is not attached. Depress the foil screen assembly release buttons on both sides of the unit and gently lift the foil screen assembly off. (fig. 1) 2. Switch the shaver on and allow fresh, cold or lukewarm water to run over the cutters. (fig. 2) 3. When finished cleaning, switch the shaver off and replace the foil 1 2 Fig. 1 Fig. 2 Axis Nitris and Axis Fuel |1 | english screen assembly, making sure it locks into place. Using the Cleaning Brush This shaver should be cleaned with the brush provided after every three wet cleanings. 1. Switch the shaver off and ensure that the power cord is not attached. Depress the foil screen assembly release buttons on both sides of the unit and gently lift off the foil screen assembly off. (fig. 1) 2. Gently brush the hairs from the inner cutters, the inside surface of the foil screen assembly and the shaver’s case. (fig. 3) To remove the inner cutters for cleaning, gently lift straight up from its mount. (fig. 4) 3. To clean the delicate outer foil screens, gently wipe the surface of the foils with tissue paper, being sure not to apply a great deal of pressure. 3 4 Axis Nitris and Axis Fuel |1 | english Fig. 3 4. When finished cleaning, reseat the inner cutters on the mounts and replace the hairpocket, making sure it locks into place. Note: to ensure proper operation, the outer foil frame assembly must be properly seated. To avoid damaging the delicate foil screens, do not Fig. 3 Fig. 4 remove them from their frame. Worldwide Voltage This shaver features worldwide automatic dual voltage conversion for 100-240 volt, 50-60 Hz AC current. You can plug the power/recharging cord into an electric outlet virtually anywhere in the world (an adapter plug may be necessary), and the shaver will adjust automatically to the required voltage. Recharging the Shaver Axis Nitris and Axis Fuel |1 | english 5 AX-3335 features a 5-stage LED power indicator. (fig. 1) AX-3331 features a green indicator light that flashes when recharging is needed, remains on while the shaver is charging, and turns off when the shaver is fully charged. Use only the power/rechar...
Эта инструкция также подходит к моделям:Электробритвы - AX3335 (3.33 mb)