Оценок - 2, средний балл: 4 ( )

Производитель: Cres Cor Размер: 520.9 kb Название файла: Язык инструкции:

2. Rinse Inside and Outside Stubborn Spots, Stains Mild abrasive made for Stainless Steel. 1. Apply with damp sponge or cloth. 2. Rub lightly. (Stainless Burnt on Foods or Grease Chemical oven cleaner made for Stainless Steel. Follow oven cleaner manufacturer's directions. Steel) Hard Water Spots & Scale Vinegar 1. Swab or wipe with cloth. 2. Rinse and dry. *MILD DETERGENTS INCLUDE SOAPS AND NON-ABRASIVE CLEANERS. MAINTENANCE INSTRUCTIONS TROUBLE-SHOOTING GUIDE AWARNING IF UNIT GETS TOO HOT OR WON’T SHUT OFF, DISCONNECT POWER AT BRANCH PANEL. DO NOT UNPLUG CORD! If hot unit is NOT working, first check the following causes: 1. Cord is unplugged from wall outlet. 3. Switch is turned off. 2. Circuit breaker/fuse to wall outlet is blown. 4. Thermostat is turned off or is set too low. =Cres Cor 5925 Heisley Road • Mentor, OH 44060-1833 877/CRES COR (273-7267) • 440/350-1100 Fax: 440/350-7267 • Ovens FL-2269 Rev. 1 (12/02) Page 7 of 10 MAINTENANCE INSTRUCTIONS TROUBLE-SHOOTING GUIDE, continued PROBLEM POSSIBLE CAUSE SOLUTION Cabinet does not 1. Fuse 1. Replace heat, or doesn't 2. Control 2. Replace heat properly 3. Sensor 3. Replace 4. Heater contactor 4. Replace 5. Loose wiring at heater contactor 5. Replace 6. On/Off Switch 6. Replace Blowers do not operate 1. On/Off Switch 1. Replace 2. Fuse 2. Replace 3. Blower 3.Replace 4. Control 4.Replace Heaters will not shut off 1. Control defective 1. Replace Vent fans do 1. Vent fan switch defective 1. Replace not shut off 2. Control compartment still hot 2.Wait until it cools. 3. Check "heaters will not shut off" Vent fans do 1. Fuse 1. Replace not operate 2. Vent fan switch defective 2. Replace 3. Vent fan defective 3. Replace Control will not switch I.Oven is in "PROBE" mode. 1. Switch to "TIMED" mode from "COOK" to "HOLD" 2.Control defective 2. Replace (timer mode) Control will not I.Oven in "TIMED" mode 1. Switch to "PROBE" mode switch from "COOK" to 2.Probe not plugged in 2.Plug in probe "HOLD" (probe mode) 3.Control defective 3.Replace I.Oven in "TIMED" mode 1. Switch to "PROBE" mode Control will not switch to 2.Probe temperature setting lower 2.Set probe temperature to "COOK" (probe mode) than probe temperature desired temperature 3.Probe not pluged in 3.Plug in probe 4.Control defective 4.Replace NOTE: Vent fans will not operate until the control compartment requires ventilation to limit temperatures. Replacement of electrical components must be done by a qualified electrician. Refer to our Service Agency fist, FL-1400 (found in the back of this manual), of authorized service centers. Instructions for replacing parts are included in replacement parts lists. Cres Cor. 5925 Heisley Road • Mentor, OH 44060-1833 877/CRES COR (273-7267) • 440/350-1100 Fax: 440/350-7267 • Ovens FL-2269 Rev. 1 (12/02) Page 8 of 10 REPLACEMENT PARTS: Include all information on nameplate when ordering parts. ( ) 0 J sM Cres Cor * §00 SB as FIGURE 2: Control Panel Hot Unit Replacement Parts Item DESCRIPTION CMP Part No. 1. Switch (ON/OFF)........................... 0808-113-01 2. Microprocessor Control.................. 0848-070-02 3. Vent Fan............................................ 0769-174 4. Fan Guard........................................ 0769-167 5...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: