Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Attach right side shelf using three 1/4-20x3/4” screws, 7mm lock washers, 7mm flat washers and 1/4” nuts, shown A. Attach rear of shelf using one 1/4-20x1.” screw, 7mm lock washer and 7mm flat washer in lower hole, shown B. Attach front of shelf and fascia using one #8x3/8” self-tapping screw and large flat washer, shown C. Attach front of shelf and fascia using one 1/4-20x3/4” screw, 7mm lock washer, 7mm flat washer and 1/4” nut, shown D/C. #8x3/8”7mm lock washer 1/4” nut self-tapping screwQty.5 7mm flat washer 1/4-20x3/4” screwQty.4 Qty.5 1/4-20x1.” screwQty.4 Qty.1Qty.1 large flat washer Qty.1 panel 7mm flat washer Fascia, right side shelf Bracket 1/4-20x3/4” screw #8x3/8” self-tapping Large flatwasher 1/4”nut 1/4”nut washer 7mm flatwasher screw 7mm lock washer 7mm flat washer1/4-20x1.” screw Back of main control panel 1/4-20x3/4” Igniter Switch screwMain control 7mm lock washer7mm lock B A CD 77 Insert flange on left sideburner shelf into side shelf brackets on side of firebox. Attach left sideburner shelf using three 1/4-20x3/4” screws, 7mm lock washers, 7mm flat washers, 1/4” nuts, shown A. Attach rear of shelf using one 1/4-20x1.” screw, 7mm lock washer, and 7mm flat washer in lower hole, shown B. Attach front of shelf and fascia using one #8x3/8” self-tapping screw and large flat washer, shown C. Under main control panel, attach front of shelf and fascia using one 1/4-20x3/4” screw, 7mm lock washer, 7mm flat washer and 1/4” nut, shown D/E. Now you may fully tighten lower screws on upper back panel. Fascia, left sideburner shelf Left sideburner shelf Flangeinto Brackets Bracket screw washerwasher #8x3/8” self-tappinglarge flatwasher 7mm lock 7mm flat BC screw 1/4-20x1.” #8x3/8” 1/4-20x3/4”Screw self-tapping screw Qty.4 1/4-20x1.” screwQty.1 7mm lock washer Qty.5 large flat washerQty.1 Qty.1 7mm flat washer 1/4” nut Qty.5 Qty.4 1/4-20x3/4” screw 1/4”nut A7mm flat washer 7mm lockwasher 1/4-20x3/4” screw Back of main control panel Control panel ED1/4”nut 7mm lockwasher 7mm flat washer removed from valve bracket Valve stem Sideburner fascia removed from valve bracket Valve stem Sideburner fascia #8-32x3/8” screw 4mm lock washer First, remove the two screws and lock washers factory attached to the sideburner valve bracket. Position sideburner valve bracket beneath sideburner shelf fascia so that valve stem comes through larger center hole in fascia. Align the holes on valve bracket with left and right holes on fascia. Secure using lock washers and screws that were removed from bracket. Next, place sideburner bezel over valve stem on front side of fascia. Align small holes on bezel with upper and lower holes on fascia, making sure “OFF” is on the top. Attach using two #8-32x3/8” screws and 4mm lock washers. Press sideburner control knob onto valve stem. Note: Use left and right #8-32x3/8” screw Note: Use upper and lower holes on fascia to Qty.2 holes on fascia to attach bezel attach valve bracket Screws and Washers 4mm lock washer Qty.2 Control knob Install bezel with “OFF” at top. OFFHi Control knob bezel Sideburner valve bracket 9 Pull out the four knobs from control panel. Insert temperature gauge stem into the bigger hole above knob bezel,shown A. Make sure the gauge is pushed in as far as it will go, then push the gauge downward until it clips into the panel, as shownin B/C. Re-install the knobs. Temperature gauge stem Knob Knob bezel Temperature gauge Control panel ACBBack of the panel 10 1010 Insert sideburner burner into left shelf.The stud on bottom of burner fits into rear small hole in sideburner drip pan onshelf, shown A.Secure burner to sideburner drip pan with one Wing nut, shown B. Make sure burner tube engages sideburner valve, shown C. Sideburner burner Wing nut BSideburner drip pan Burner tube Valve CWing nut ASideburner drip pan Qty.1 11 Under sideburner shelf, attach sideburner ignitor wire to electrode, shown A. Place sideburner grate onto sideburner shelf, aligning grate legs with holes in shelf, shown B. ASideburner Ignitor Wire Electrode Sideburner grate B 12 1212 Insert front brace under control panel and between cart side panels. Make sure door hinge pins are on the top side and facing the front. Secure using two 1/4-20x1.” screws, 7mm lock washers, and 7mm flat washers on each side. 1/4-20x1.” screw 7mm lock washer 7mm flat washer Door Hinge Pin Front brace 1/4-20x1.” 7mm Lock washer screw Qty.4 Qty.4 Qty.4 7mm flat washer 13 13 Inside of cart, insert rear shield into left slot(#1) on top of lower back panel. Insert left grease tray rail into slot(#2) beneath grease tray opening in upper back panel, shown A. Attach front shield and left grease tray rail under front brace(#4 and #5) with two #8x3/8” self-tapping screws, shown B. Insert right grease tray rail into slot(#3) and attach it under front brace(#6) with one #8x3/8” self-tapping screws, shown A/B. *This side UP Tank heat shieldRear Front 20 Tank heat shield Tank heat shield Cart lower back panel Right rail Left rail Front ...
Эта инструкция также подходит к моделям:Электрические печи - 415.9011211 (3.84 mb)