Оценок - 2, средний балл: 3.5 ( )

Производитель: Ariston Размер: 1.44 mb Название файла: Язык инструкции:

Maintenance Inside the oven We recommend you clean your oven each time you use it, especially after cooking roasts. In fact, it is advisable to prevent food residue from building up during cooking: the residue would be re-cooked each time the oven is used and would char and release smoke and unpleasant odours. Oven exterior Clean the enamelled or stainless steel exterior surfaces of your oven using a sponge soaked in soapy water, making sure you rinse and dry these thoroughly, without using abrasive or corrosive products which could damage them. Stainless steel Rinse stainless steel parts and dry them thoroughly using a soft cloth. Use a specific non-abrasive product to remove tougher stains, Using aluminium foil To avoid having to clean the bottom of the oven, you may be tempted to line the same with some aluminium foil. We strongly advise against this.The aluminium foil sheet in direct contact with the heated enamel coating could melt and damage the enamel coating inside the oven irreversibly. Cleaning the rotisserie and other accessories The rotisserie can be removed completely thanks to the 2 wing nuts.The elements comprising the rotisserie assembly should be cleaned together with the other accessories (dripping pan, grid) in the sink using a damp sponge and ordinary detergent or even in your dishwasher. Disassembling the oven door The oven door can easily be removed to clean the space between the bottom of the door and the front of the oven.To disassemble the door, proceed as follows: • open the oven door fully, • lift up and turn the small levers situated on the two hinges, • shut the door, but not completely, • grip the door on the two external sides and pull it towards you, pulling it out of its seat. 35 Disassembling oven door FO 97 P - FD 97 P - FD 96 P 1 32 Disassembling oven door FC 97 P - FB 86 P 1 2 3 Re-assemble the door by following the above procedures backwards. Replacing the oven lamp • Always unplug the appliance from the mains or switch off the main switch before all operations. • With the aid of a narrow, flat item (such as a screwdriver or a spoon handle, etc…), remove the glass cover. • Unscrew the lamp and replace it with another featuring the same characteristics: - voltage 230/240 W - wattage 15 W -type E 14 • Replace the glass cover and ensure you reposition the seal correctly. Glass door Seal Lamp Oven compartment Installation Built-in installation This oven can be built into all standard furniture cabinet units featuring dimensions conforming to European standards.No particular precautions need to be taken when performing the built-in installation of the oven, thanks to: -its reinforced insulation that limits the heat exchanges -its frontal cooling ventilation requiring no air inlet. Installation must be performed by a qualified professional and in all cases in compliance with the safety norms in force, failing which the appliance guarantee will not be valid in the event of an accident caused by incorrect installation. This is also important for the safety of the user and the long life of your appliance. 595 mm. 595 mm. 545 mm. 5 mm. 567 mm.575-585 mm.558 mm. 595 mm.45 mm.min. 45 mm.min. 20/28 mm. 20/23 mm. 595 mm. 595 mm. 20/28 mm. 545 mm. 5 mm. 567 mm. 20/23 mm.593 mm.45 mm. 558 mm. 36 The panels of the adjacent cabinets must be made of heat- resistant material. In particular, cabinets with a veneer exterior must be assembled with glues which can withstand temperatures of up to 100°C. In compliance with current safety standards, contact with the electrical parts of the appliance must not be possible once it has been installed. All protective parts which ensure the safe operation of the appliance must be removable only with the aid of a tool. Built-in installation of FO97 P - FD97 P - FD96 P - FB86 P Position the 4 tabs on the sides of the oven in correspondence with the 4 holes on the perimeter of the frame. In particular, if the cabinet side panel: • is 20 mm thick: the removable part of the tab must be removed (Fig. A); • is 18 mm thick: use the first groove, which is factory-set (Fig. B); • is 16 mm thick: use the second groove (Fig. C). Fig. A Fig. B Fig. C To fasten the oven to the cabinet, open the oven door and screw the 4 screws (supplied with the appliance) into the 4 holes located on the perimeter of the frame. Installation Built-in installation of FC 97 P (see figure on the right) 1. Place brackets "A" well against the oven support blocks "B". 2. Place the tabs "C" well against brackets "A". In particular, if the cabinet side panel: • is 16 mm thick: mount the tab so that the number 16 it features is facing you; • is 18 mm thick: mount the tab so that the part without any wording is facing you; • is 20 mm thick: do not mount the tab. 3. Fasten the brackets and tabs on the oven cabinet side panel using screws "D". 4. Fasten the oven to the cabinet using the screws and plastic washers "E". D A B D D 16 16 16 16 C C C E E Electrical connection Connection First check t...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: