Оценок - 4, средний балл: 4 ( )

Производитель: Blodgett Размер: 2.47 mb Название файла: Язык инструкции:

• Improper rack position being used. See the Broiling guide. • Food being cooked in a hot pan. Use the broiling pan and grid that came with your oven. Make sure that it is cool. • Cookware not suited for broiling. Use the broiling pan and grid that came with your oven. • The probe is plugged into the outlet in the oven. Remove the probe from the oven. • Aluminum foil used on the broiling pan and grid has not been fitted properly and slit as recommended. • In some areas the power (voltage) may be low. Preheat the broil element for 10 minutes. Broil for the longest period of time recommended in the Broiling guide. OVEN WILL NOT • The oven temperature is too high to set a self-clean operation. SELF CLEAN Allow the oven to cool and reset the controls. • Oven controls improperly set. See the Using the Self-Cleaning Oven section. • The probe is plugged into the outlet in the oven. Remove the probe from the oven. “CRACKING” OR “POPPING” SOUND • This is normal. It is the sound of the metal heating and cooling during both cooking and cleaning functions. EXCESSIVE SMOKING DURING CLEAN CYCLE • Excessive soil. Press the CLEAR/OFF pad. Open the windows to rid the room of smoke. Wait until the LOCKED light goes off. Wipe up the excess soil and reset the clean cycle. Before You Call For Service… Wall Oven Trouble-PROBLEM POSSIBLE CAUSE shooting tips OVEN DOOR WILL NOT OPEN AFTER A CLEAN CYCLE • The oven is too hot. Allow the oven to cool below locking temperature. OVEN NOT CLEAN AFTER A CLEAN CYCLE • Oven controls improperly set. See the Using the Self-Cleaning Oven section. • Oven was heavily soiled. Clean up heavy spillovers before starting the clean cycle. Heavily soiled ovens may need to self-clean again or for a longer period of time. “LOCK” FLASHES IN THE DISPLAY • The self-clean cycle has been selected but the door is not closed. Close the oven door. LOCKED LIGHT IS ON WHEN YOU WANT TO COOK • The oven door is locked because the temperature inside the oven has not dropped below the locking temperature. Press the CLEAR/OFF pad. Allow the oven to cool. CONTROL SIGNALS AFTER ENTERING COOKING TIME OR DELAY START • You forgot to enter a bake temperature or cleaning time. Press the BAKE pad and desired temperature or the SELF CLEAN STD/LOW pad and desired clean time. “F— AND A NUMBER OR LETTER” FLASH IN THE DISPLAY • You have a function error code. Press the CLEAR/OFF pad. Allow the oven to cool for one hour. Put the oven back into operation. • Disconnect all power to the oven for 30 seconds and then reconnect power. If the function error code repeats, call for service. DISPLAY GOES BLANK • A fuse in your home may be blown or the circuit breaker tripped. Replace the fuse or reset the circuit breaker. • The clock is in the black-out mode. See the Oven Control, Clock and Timer section. DISPLAY FLASHES • Power failure. Reset the clock. UNABLE TO GET THE DISPLAY TO SHOW “SF” • Oven control pads were not pressed properly. The BAKE and the BROIL HIGH/LOW pads must be pressed at the same time and held for 3 seconds. “PROBE” APPEARS IN THE DISPLAY • This is reminding you to enter a probe temperature after plugging in the probe. Enter a probe temperature. POWER OUTAGE, CLOCK FLASHES • Power outage or surge. Reset the the clock. If the oven was in use, you must reset it by pressing the CLEAR/OFF pad, setting the clock and resetting any cooking function. STEAM FROM THE VENT • When using the convection feature, it is normal to see steam coming out of the oven vent. As the number of racks or amount of food being cooked increases, the amount of visible steam will increase. “BURNING” OR “OILY” ODOR EMITTING FROM THE VENT • This is normal in a new oven and will disappear in time. To speed the process, set a self-clean cycle for a minimum of 3 hours. See the Using the Self-Cleaning Oven section. STRONG ODOR • This is temporary. An odor from the insulation around the inside of the oven is normal for the first few times the oven is used. FAN NOISE • A cooling fan or a convection fan (depending on the function you are using) may automatically turn on. This is normal. The cooling fan will turn on to cool internal parts. It may run for up to 1-1/2 hours in 30. models and up to 2 hours in 27. models after the oven is turned off. The convection fan will cycle on and off until the function is over or the door is opened. GE Appliances Consumer Product Ownership Registration Important Mail Today Place 1st Class Letter Stamp Here General Electric Company Warranty Registration Department P.O. Box 32150 Louisville, KY 40232-2150 Consumer Product Ownership Registration Dear Customer: Thank you for purchasing our product and thank you for placing your confidence in us. We are proud to have you as a customer! Follow these three steps to protect your new appliance investment: . . 1 1 Complete and mail your Consumer Product Ownership Registration today. Have the peace of mind of knowing we can contact you in the unlikely event of a safety modification. 2 A...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: