Войти:
Оценок - 5, средний балл: 3.8 ( )

Инструкция по эксплуатации CDA, модель SVA 100 PP

Производитель: CDA
Размер: 1.27 mb
Название файла: 3df873a2-d698-474a-88d1-031f0fc7b7c7.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


8b). – Hold the door as shown in fig. 8. – Gently close the door (fig. 8c) until left and right hinge levers A are hooked to part B of the door (fig. 8b). – Withdraw the hinge hooks from their location following arrow C (fig. 8d). – Rest the door on a soft surface. – To replace the door, repeat the above steps in reverse order. BAFig. 8b Fig. 8a A B CFig. 8 Fig. 8d Fig. 8c C 19 Oven Door - Removable Inner Pane of Glass Cleaning the Panes of Glass The oven door is fitted with no. 2 panes: - no. 1 outside; - no. 1 inner; To clean the panes on both sides it is necessary to remove the inner pane as follows. Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since they scratch the surface, which may result in shattering of the glass. Removing the Inner Pane of Glass The oven door has two panes. To clean these, you need to remove the inner pane. 1. Lock the door open: – Fully open the oven door (fig. 9). – Fully open the lever A on the left and right hinges (Fig 10). – Gently close the door (Fig. 11) until the left and right hinges are hooked to part B of the door (Fig. 10). 2. Remove the inner pane: – Remove the seal G by unhooking the no. 3 fixing hooks (fig. 12). – Gently pull out the inner pane of glass (Fig. 13). – Clean the glass with an appropriate cleaner. Dry thoroughly, and place on a soft surface. Now you can also clean the inside of the outer glass. Fig. 13 GFig. 12 BAFig. 11 Fig. 10 Fig. 9 A B G Fig. 13 GFig. 12 BAFig. 11 Fig. 10 Fig. 9 A B G 20 20 Replacing the Inner Pane of Glass 1. Make sure the door is locked open (see fig. 11). 2. Replace the inner pane: – Check that the four rubber pads are in place (D in Fig. 14). – Check that you are holding the pane the correct way. You should be able to read the wording on it as it faces you. – Insert the pane in the left E and right F slide guides (fig. 15), and gently slide it to the retainers H (fig. 16). – Reassemble the seal G in the correct way (fig. 17) by hooking the no. 3 fixing hooks in the proper holes (fig. 18). – Unlock the oven door by opening it completely and closing the lever A on the left and right hinges (Fig. 19). AFig. 14 EFHFig. 16 HGFig. 17 Fig. 18 It is normal the opened gap between the top edge of the inner glass and the sealed gasket. This allows the cooling air circulation. The oven door has a sealed gasket in the top part. H D G A F E Fig. 15 Fig. 19 ADVICE FOR THE INSTALLER Important Appliance installation and maintenance must only be carried out by QUALIFIED TECHNICIANS and in compliance with the local safety standards. • Failure to observe this rule will invalidate the warranty. • Always disconnect the appliance from the electrical supply before carrying out any maintenance operations or repairs. • The walls surrounding the oven must be made of heat-resistant material. • Taking care NOT to lift the oven by the door handle. WARNING When correctly installed, your product meets all safety requirements laid down for this type of product category. However special care should be taken around the rear or the underneath of the appliance as these areas are not designed orintended to be touched and may contain sharp or rough edges, that may cause injury. 22 22 Important The oven can be fitted in standard units, width and depth 60 cm. Installation requires a compartment as illustrated in figures 20 and 21. On the lover side, the oven must lay on supports standing the oven weight. 56050585Fig. 20 560550 min59159459454020536 minFig. 21 23 To ensure internal ventilation, aeration channels must be provided as illustrated in the figures 22 and 23. 30 mm 600 50 mm 50 550 Fig. 22 Fig. 23 24 24 Fixing the Oven Introduce the oven into the furniture opening and fix it with screws (not supplied) as figure 24. It is essential that the oven rests on a surface which will support its weight, as the screw fixing is only complementary. Note It is essential that when installing your oven adequate air circulation is allowed for within the installation. See figures 22 - 23. Inadequate air circulation may greatly impair the performance of your oven and may effect adjacent cabinets due to an increase in temperature. Caution Do not lift this oven by the door handle Adjust the hinges of furniture doors adjacent to the oven to allow a 4-5 mm gap between the furniture door and the oven frame. Fig. 24 25 OVEN DOORLOWER TRIMAIR FLOWIMPORTANT: – To avoid damage to the lower trim please note the following instructions. – The lower trim is designed to allow for good air circulation and the correct opening of the oven door. – To ensure the trim is not damaged due to the appliance being placed on the floor, the appliance should be suitably supported as in below illustrations. – After installation the appliance door should be slowly opened to ensure no damage has occurred. – No responsibility for lower trim damage will be accepted if these instructions have not been followed. Fig. 25 Air Flow Oven Door Lower Trim 25 OVEN DOORLOWER TRI...


Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории