Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
The padlock on the display is flashing Door lock system fault Call CDA Customer Care The oven light is not working Light fault Replace the bulb The pyrolysis programmes do not start The door is not properly closed Close the door completely Door lock system fault Call CDA Customer Care The oven starts beeping during cooking The oven is at the required temperature The oven starts beeping at the end of the cooking programme The programme has finished Error Code Fault F01 Temperature sensor error F02 Overheated oven . First ensure there is adequate ventilation to the oven as described on page 16. F03 Pyrolysis failure (door locked) F04 Door interlock F05 Other cooking faultF10 Information only – power cut during cooking AUTOAuto stop. The oven is equipped with an auto stop function to automatically switch off the oven if it is in continuous use for more than 23 hours and 30 minutes. 15 Installation Important If the oven is being installed into a built under oven housing unit ensure that the front rail at the top of the unit is not installed as it could restrict ventilation. Ensure that air can flow freely around the housing area. If the oven is being installed into a fully enclosed built-under oven housing unit it may be necessary to cut a small slot in the top of the plinth fitted under the unit. Cut a section 400mm wide and a minimum of 15mm high to allow air to pass under the unit. Alternatively cut a section 400 x450mm in the base of the carcass as indicated. Failure to allow adequate ventilation to the appliance may result in overheating or damage to adjacent units and could invalidate the warranty. The walls of the kitchen units must be able to withstand temperatures of 75. above ambient (typically this is between 90. and 100.). This appliance is type X installation. When correctly installed ensure that there is a gap of 6mm minimum between the sides of the oven and adjacent furniture doors. Lift the oven carefully into position on the shelf, taking care NOT to lift it by the door handle. If you open the oven door, you will see 2 screw holes, 1 on each side of the oven. The oven should then be secured to the housing by fitting screws into these holes. Remember the housing should not be free standing but be secured to the wall and/or adjacent fittings. How to install your oven You will need the following housing area fit your oven correctly. The oven is designed to fit into a cabinet of 600mm width. The oven can be built in or built under the kitchen units, but you must ensure that it is properly ventilated. In the diagram the built-in oven is ventilated by means of a space at the top of the kitchen cabinet. There are many other methods of ventilating your oven - Consult a qualified engineer for advice. fig. 18 Dimensions Oven Housing Height (mm) 594 585 Width (mm) 592 560 Depth (mm) 561 550 (min) 58556055070 550 592 16 Installation Important If the oven is being installed into a built under oven housing unit ensure that the front rail at the top of the unit is not installed as it could restrict ventilation. Ensure that air can flow freely around the housing area. If the oven is being installed into a fully enclosed built-under oven housing unit it may be necessary to cut a small slot in the top of the plinth fitted under the unit. Cut a section 400mm wide and a minimum of 15mm high to allow air to pass under the unit. Alternatively cut a section 400 x450mm in the base of the carcass as indicated. Failure to allow adequate ventilation to the appliance may result in overheating or damage to adjacent units and could invalidate the warranty. The walls of the kitchen units must be able to withstand temperatures of 75. above ambient (typically this is between 90. and 100.). This appliance is type X installation. When correctly installed ensure that there is a gap of 6mm minimum between the sides of the oven and adjacent furniture doors. Lift the oven carefully into position on the shelf, taking care NOT to lift it by the door handle. If you open the oven door, you will see 2 screw holes, 1 on each side of the oven. The oven should then be secured to the housing by fitting screws into these holes. Remember the housing should not be free standing but be secured to the wall and/or adjacent fittings. How to install your oven You will need the following housing area fit your oven correctly. The oven is designed to fit into a cabinet of 600mm width. The oven can be built in or built under the kitchen units, but you must ensure that it is properly ventilated. In the diagram the built-in oven is ventilated by means of a space at the top of the kitchen cabinet. There are many other methods of ventilating your oven - Consult a qualified engineer for advice. fig. 18 Dimensions Oven Housing Height (mm) 594 585 Width (mm) 592 560 Depth (mm) 561 550 (min) 58556055070 550 592 16 Mains Electricity Connection Warning! This appliance must be earthed We recommend that the appliance is connected by a qualified electrician, who is ...