Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
3 & 4. . If there is an existing housing unit it must be removed. . The dimensions given provide adequate air circulation around the unit within the cabinet, ensuring compliance with BS EN60-335. . Enquiries regarding the installation of the cooker point, if required, should be made to your Regional Electricity Company to ensure compliance with their regulations. . This appliance must not be installed on a wooden base board. . The cooker point should be within 2m of the appliance to make it accessible to switch off the appliance in case of an emergency. . To protect the hands, wear gloves when lifting the oven into its housing. NOTE: HOUSE CIRCUIT Earth leakage / continuity tests must be carried out before the appliance is connected to the mains supply and re-checked after fitting. Fig. 3 Fig. 4 38 INSTALLATION INSTRUCTIONS PREPARING CABINET FOR FITTING OVEN . Make sure the space between the cabinets is the correct size for the appliance to be fitted (Ref. Fig. 5 & 6). . The plinth board spanning the space into which the appliance is to be installed should be removed. . If the size between adjacent cabinets is 605610* mm, then the cabinets should be modified so that the recommended dimension of at least 600605mm is maintained. . The adjacent cabinets must be stable and firmly secured to the wall or floor. If necessary, make arrangements to ensure the work surface below which the oven will rest is level. . Drill two pilot screw holes into the sides of the adjacent cabinets, in the positions indicated by Fig. 5. . Fit the appliance mounting brackets using the two holes indicated in Fig. 7 to the adjacent cabinets (Ref. Fig. 5 & 6 ). Fig. 5 Fig. 7 Fig. 6 39 INSTALLATION INSTRUCTIONS . Check that the mounting brackets are level. They can be adjusted if necessary by using the extra holes at the ends of the brackets. Once the brackets are level, drill a pilot hole through the central hole in the bracket and fit the remaining screw. HOW TO FINISH UNPACKING . Place appliance next to the space in which it will be installed. See Fig 8. . Remove the appliance packing except for bottom tray which should be left in position until the appliance is ready to be fitted into its cabinet. . Ensure the owner is given these operating instructions. NOTE: It is imperative that the appliance is left inthe base to protect both the appliance and thefloor. Fig. 8 Important: Switch off at mains, miniature circuit breaker and, if appropriate, removefuse before commencing any electrical work. 40 INSTALLATION INSTRUCTIONS TO REMOVE COVER OF MAINS TERMINAL From the rear of the appliance, remove mains input terminal cover to gain access to terminal block. . First remove retaining screw with pozidrive screwdriver. See Fig. 9. Fig. 9 . Prise cover loose using screwdriver in position (1) then lever off with screwdriver in position (2) at either side. See Fig. 10. Fig.10 Lift cover and remove screw from cable clamp. See Fig. 11. Fig.11 41 INSTALLATION INSTRUCTIONS CONNECTING TO THE MAINS TERMINAL Warning: This appliance must be earthed. . We recommend you use a new length of 6mm2 twin core and earthed cable to ensure your safety. . Make connection as shown in Fig. 12 by proceeding as follows:. Preform wires to the appropriate shape to suit fitting into the mains terminal block. . Strip inner insulation on wires using wirestrippers. . Twist the bared wires using pliers. . Cut bared wires 10mm away from the end of the inner insulation. Where uninsulated Earth wires are used ensure they are suitably sheathed to leave 10mm bare wire fit into the terminal. . Clamp bare wires into the relevant terminal and check they are held by tugging each one in turn. . Clamp the mains cable securely ensuring 5mm of the outer insulation is inside the terminal block and that the wires are not taught but not so slack as to cause any fouling. See Fig. 12. . Connect the remaining end of the mains cable to the cooker point / junction box. . Please fuse / miniature circuit breaker in circuit and switch on at mains. Fig.12 42 INSTALLATION INSTRUCTIONS CHECKING ELECTRICAL CONNECTIONS . Confirm the appliance is correctly connected by switching on and observing the various oven functions indicators. . The electronic timer will flash on and off. CONNECTING TO A HOB OR COOKER POINT . Either follow in general terms the instructions for connecting to the terminal block or refer to the hob suppliers installation instructions. Feed the cable through the cabinet and arrangeto route the cable away from the appliance. NOTE: HOUSE CIRCUIT Earth leakage / continuity tests must be carried out before the appliance is connected to the mains supply and re-checked after fitting. INSTALLATION INSTRUCTIONS FITTING INTO THE SPACE BETWEEN CABINETS IMPORTANT: Ensure that the oven is switched off at the wall before any furtherwork is carried out. . Ensure the appliance is in front of the cabinet. See Fig. 13. . Take out all oven furniture before installation to reduce the weight you need to lif...