Оценок - 4, средний балл: 4.5 ( )

Производитель: AEG Размер: 1.74 mb Название файла: 945539EN.pdf Язык инструкции:

Activate the Settings menu: 1. If necessary, deactivate the appliance . 2. Touch and hold for three seconds. The display shows "SET1" and "1" flashes. 3. Touch / to set the setting. 4. Touch . 5. Touch / to change the value of the setting. 6. Touch . Automatic switch-off For safety reasons the appliance deactivates automatically after some time: • if an oven function operates. • if you do not change the oven temperature. Oven temperature Switch-off time 30 °C -120 °C 12.5 h. 120 °C -200 °C 8.5 h. 200 °C -230 °C 5.5 h. After an automatic switch-off, touch a sensor field to operate the appliance again. The Automatic switch-off works with all oven functions, apart from Light, Low temperature cooking, Core temperature sensor, Duration, End, Time delay. Brightness of the display There are two modes of display's brightness: • Night brightness - when the appliance is off, the brightness of the display is lower between 22:00 and 06:00; • Day brightness: – when the appliance is on; – if you touch any of the sensor fields during night brightness (apart from ON/OFF), the display goes back to day brightness mode for next 10 seconds; Care and cleaning 23 – if the appliance is off and you set the minute minder. When the minute minder function ends, the display goes back to night brightness; Cooling fan When the appliance operates, the cooling fan activates automatically to keep the surfaces of the appliance cool. If you deactivate the appliance, the cooling fan can continue to operate until the appliance cools down. CARE AND CLEANING WARNING! Refer to "Safety information" chapter. Notes on cleaning: • Clean the front of the appliance with a soft cloth with warm water and cleaning agent. • To clean metal surfaces use a usual cleaning agent. • Clean the appliance interior after each use. Then you can remove dirt more easily and it does not burn on. • Clean stubborn dirt with a special oven cleaner. • Clean all accessories (with a soft cloth with warm water and cleaning agent) after each use and let them dry. • If you have nonstick accessories, do not clean them using an aggressive agents, sharp edged objects or dishwasher. It can cause a damage to the nonstick coating. Steam cleaning 1. Remove the worst of the residual dirt manually. 2. Put approximately 250 ml of water and 3 tablespoons of vinegar directly in the steam generator. 3. Set Steam cleaning function. Refer to "Oven functions". The display shows the duration (15 minutes) and preset temperature (96°C). Touch OK. The cleaning starts. 4. An acoustic signal sounds when steam cleaning is completed. Touch any sensor field to stop the signal. 5. Wipe out the appliance with a soft cloth. Remove water from the steam generator with the Sponge and rub dry. Keep the door open for approximately 1 hour to let the appliance dry fully. You can use the End function to delay start of cleaning process. Refer to "Setting the END". Shelf support You can remove the shelf support to clean the side walls. 24 24 Care and cleaning Removing the shelf support 1. Carefully pull the support up and out of the front catch. 2. Lightly move the support on the front catch inwards. 3. Pull the support out of the rear catch. Installing the shelf support Install the shelf support in the opposite sequence. Steam generation system CAUTION! Dry the steam generator after each use. Soak up water with the Sponge. Remove a limescale with water and vinegar. CAUTION! Chemical de-scaling agents can cause a damage to the enamel. Obey instructions of the manufacturer! Care and cleaning 25 Cleaning the Water Drawer and the Steam Generator: 1. Fill the water and vinegar mixture (approximately 250 ml) through the water drawer in the steam generator. Wait for approximately 10 minutes. 2. Remove the water and vinegar with the Sponge. 3. Use clean water (100-200 ml) to flush the steam generation system through the water drawer. 4. Remove water from the steam generator with the Sponge and rub dry. 5. Keep the door open to let the appliance dry fully. Oven lamp WARNING! There is a risk of electrical shock. The oven lamp and the lamp glass cover can be hot. Before you change the oven lamp: • Deactivate the appliance. • Remove the fuses from the fuse box or deactivate the circuit breaker. CAUTION! Put a cloth on the bottom of the interior of the appliance. It prevents damage to the lamp glass cover and the cavity. Replacing the lamp: 1. You can find the lamp glass cover at the cavity ceiling. Turn the lamp glass cover counterclockwise to remove it. 2. Remove the metal ring and clean the glass cover. 3. If necessary, replace the lamp with applicable 300°C heat-resistant lamp. Use the same lamp type. 4. Fit the metal ring to the glass cover. 5. Install the glass cover. Replacing the oven lamp: 1. You can find the lamp glass cover at the left side of the cavity. Remove the left shelf support. 2. Use a torx 20 screwdriver to remove the cover. 3. Remove and clean the metal frame and the seal. 4. Replace the oven lamp with app...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: