Оценок - 5, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
• Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Unauthorized changes or modification to this system can void the user’s authority to operate this equipment. CE mark for European Harmonized Standards CE mark which is attached to our company’s products of AC mains operated apparatus until December 31, 1996 means it conforms to EMC Directive (89/336/EEC) and CE mark Directive (93/68/EEC). And, CE mark which is attached after January 1, 1997 means it conforms to EMC Directive (89/336/EEC), CE mark Directive (93/68/EEC) and Low Voltage Directive (73/23/EEC). Also, CE mark which is attached to our company’s products of Battery operated apparatus means it conforms to EMC Directive (89/336/EEC) and CE mark Directive (93/68/EEC). IMPORTANT NOTICE TO CONSUMERS This product has been manufactured according to strict specifications and voltage requirements that are applicable in the country in which it is intended that this product should be used. If you have purchased this product via the internet, through mail order, and/or via a telephone sale, you must verify that this product is intended to be used in the country in which you reside. WARNING: Use of this product in any country other than that for which it is intended could be dangerous and could invalidate the manufacturer’s or distributor’s warranty. Please also retain your receipt as proof of purchase otherwise your product may be disqualified from the manufacturer’s or distributor’s warranty. Introduction Installing the batteries Slide and remove the battery compartment cover located on the back of the GA-40. Insert the batteries ensuring that you observe the correct polarity, and replace the cover. If the GA-40 malfunctions, and you are unable to solve the problem by turning the power off and on again, try removing the batteries and then reinstall them. The included batteries are provided for the purpose of verifying operation and therefore may have a shorter lifetime than usual. When the batteries run low, a battery indicator will appear in the left of the display. When this indicator appears, replace the batteries as soon as possible. Power-off the GA-40 before you replace the batteries. Using the stand By opening the stand located on the back, you can position the GA-40 at a convenient angle. Using the tuner Tuning guide [STANDBY/ON] button Display Meter mode This mode lets you tune using the meter in the display. 1 Connect the tuner. The connection method will depend on the type of guitar you're using. When tuning an electric guitar or bass Be sure to use an instrument cable for connection to the GA-40's INPUT jack. You can't use the internal mic if a plug is inserted in the INPUT jack. If you're performing on stage, it is convenient to use the GA-40's OUTPUT jack. Connect your guitar to the GA-40's INPUT jack, and then connect your amp to the OUTPUT jack. The sound of your instrument will be sent from the GA-40's OUTPUT jack to your amp, allowing you to tune or perform while the GA-40 remains connected. If you've connected the OUTPUT jack to your amp etc., you must insert a cable into the INPUT jack. If nothing is connected to the INPUT jack, the internal mic will be automatically used. In this case, sound entering the internal mic could cause feedback, possibly damaging your amp. [GUITAR/BASS] button [FLAT] button INPUT jack Speaker OUTPUT jack Internal mic [SOUND] button When tuning an acoustic guitar If you're using a separately sold Korg CM-100 contact mic, connect the CM-100's plug to the GA-40's INPUT jack. If you're using the internal mic, don't connect anything. 2 Press the [STANDBY/ON] button. The GA-40 will be in Meter mode. The power will turn off automatically if the tuner is not used for approximately twenty minutes. 3 Press the [GUITAR/BASS] button to select the instrument you're tuning. The tuning pitches will be as follows. GUITAR: 7B, 6E, 5A, 4D, 3G, 2B, 1E BASS: LB (Low B), 4E, 3A, 2D, 1G, HC (High C) 4 Play a single note on your instrument. The name of the note closest to the note you played will appear in the upper left of the display. Tune your instrument so that the desired note name appears. If you're using the internal mic, position the mic as close as possible to your instrument, and ensure that extraneous background sounds are not picked up by the mic while tuning. 5 While playing a single note, tune your instrument so that the indicator in the center of the tuning guide is lit (if the tuning reference is A=440 Hz). The left indicator of the tuning guide will light if the pitch of your instrument is too low, and the right indicator will light if the pitch is too high. Each step in the meter is approximately 2 Hz. Sound Out mode This mode lets you listen to a reference tone while you tune. 1 Perform steps 2 and 3 of “Meter mode.” 2 Press the [S...