Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
See Figure 23. 10.The nuts on the flat head cap screws can be reached from underneath using a 1/2-inch socket, universal, and extension. See Figure 24. 11. Replace or sharpen chipper blade. The blade can be sharpened with a file or on a grinding wheel. 12.When sharpening blade, protect hands by using gloves and follow the original angle of grind. 13.Reassemble by performing the previous steps in the opposite order and manner of removal. NOTE: Tighten blade screws to 210 - 250 in-lbs. Make certain chipper blade is reassembled with the sharp edge facing upward. Storing Your Yard Vacuum 1. Clean the equipment thoroughly. 2. Wipe equipment with an oiled rag to prevent rust. 3. Refer to engine manual for correct engine storage instructions. 4. Store unit in a clean, dry area. Do not store next to corrosive materials such as fertilizer. Figure 3 .................................................................. Figure 4 ........................ Maintaining Your Yard Vacuum NOTE: Tighten blade screws to 210-250 in.-lbs. Make certain chipper blade is reas- sembled with the sharp edge facing upward. 17 Problem Cause Remedy Engine fails to start 1. Throttle lever not in correct starting position. 2. Spark plug wire disconnected. 3. Choke not in CHOKE position (if equipped). 4. Fuel tank empty or stale fuel. 5. Engine not primed (if equipped). 6. Faulty spark plug. 7. Safety switch not depressed. 8. Safety switch wire is not connected to engine or not properly grounded. 1. Move throttle lever to FAST or START position. 2. Connect wire to spark plug. 3. Move choke lever to CHOKE position. 4. Fill tank with clean, fresh gasoline. 5. Prime engine as instructed in Engine Manual. 6. Clean, adjust gap, or replace. 7. Safety switch must be depressed by the front tab on the bag handle when securing the bag. 8. Connect safety switch wire to engine connector and ground to mounting bracket. Engine runs erratic 1. Spark plug wire loose. 2. Unit running on CHOKE (if equipped). 3. Blocked fuel line or stale fuel. 4. Low engine RPM. 5. Water or dirt in fuel system. 6. Dirty air cleaner. 7. Carburetor out of adjustment. 1. Connect and tighten spark plug wire. 2. Move choke lever to OFF position. 3. Clean fuel line; fill tank with clean, fresh gasoline. 4. Always run engine at full throttle. 5. Drain fuel tank. Refill with fresh fuel. 6. Refer to engine manual. 7. See authorized service dealer. Engine overheats 1. Engine oil level low. 2. Dirty air cleaner. 3. Carburetor not adjusted properly. 1. Fill crankcase with proper oil. 2. Refer to engine manual. 3. See authorized service dealer. Occasional skips (hesitates) at high speed 1. Spark plug gap too close. 2. Carburetor idle mixture adjustment improperly set. 1. Adjust gap to .030”. 2. See authorized service dealer. Excessive Vibration 1. Loose parts or damaged impeller. 1. See authorized service dealer. Unit does not 1. Discharge area clogged. 1. Stop engine immediately and discharge disconnect spark plug wire. Clean flail screen and inside of discharge opening. 2. Foreign object lodged in impeller. 2. Stop engine and disconnect spark plug wire. Remove lodged object. 3. Low engine RPM. 3. Always run engine at full throttle. 4. Vacuum bag is full. 4. Empty bag. Rate of discharge 1. Low engine RPM. 1. Always run engine at full throttle. slows considerably 2. Chipper blade dull. 2. Replace chipper blade or see your or composition of authorized service dealer. discharged material changes Unit fails to propel itself 1. Drive control cable out of adjustment. 1. Follow adjustment procedure or slips when drive in Servicing Your Yard Vacuum control is engaged 2. Drive belt worn or damaged. section of manual. 2. See authorized service dealer. 6 Trouble Shooting For repairs beyond the minor adjustments listed here, contact an authorized service dealer. 18 For parts and/or accessories please call 1-866-840-6483, or 1-330-558-7220. NOTES: Use this page to make notes and write down important information. 19 20 Model 070 / 071 53 54 52 51 5 52 59 6 46 49 72 68 50 16 22 17 33 30 81 55 12 48 21 20 19 18 15 65 58 56 23 65 47 67 61 63 36 65 60 82 31 70 41 44 64 15 73 57 15 69 80 76 74 43 45 11 13 3 7 16 8 40 27 35 37 34 32 38 28 2 39 24 4 25 10 66 71 75 78 77 79 42 14 42 9 14 29 6 26 A A B B 62 7 Parts List To order replacement parts, contact 1-800-520-5520, 1-330-558-7220 or visit Ref. Part No. Description 1. 736-0451 Saddle Washer, .320 x.93 2. 749-04163 Upper Handle 3. 720-0279 Knob 4. 710-1205 Eye Bolt 5. 781-1056 Upper Handle Bracket 6. 710-0726 Hex Cap Screw 5/16-12 x.750 7. 720-04072 Star Knob 8. 710-1174 Carriage Bolt 9. 731-04911 Nozzle Handle Clip 10. 749-04165 Lower Handle 11. 711-1293 Studs 12. 710-0703 Carriage Screw 1/4-20 x.75 13. 712-0397 Wing Nut 1/4-20 14. 710-1611B TT Screw, 5/16-18 x .750 15. 710-0599 Screw, 1/4-20 x .500 16. 712-0442 Cap Lock Nut, 1/4-20 17. 710-0751 Hex Cap Screw 1/4-20 x.620 18. 681-0195 Hose Base Adapter Assembly (Incl. Ref.#...
Эта инструкция также подходит к моделям:Измельчители садовые - 071 (3.34 mb)