Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Close finger tight only. Forcing will cause damage. 2. Open one turn (counterclockwise). 3. Close idle adjusting needle (figure 11) by turning to right (clockwise). Close finger tight only. Forcing will cause damage. 4. Open one and one-half (1 Vz) turns (counterclockwise). 5. Start engine. Follow starting instructions page 5. 6. With throttle open (carburetor control at RUN or FAST position) adjust power adjusting needle one-eighth (118) turn at a time forward or backward until engine runs smoothly. If engine tends to stall under load enrich mixture slightly (counterclockwise). 7. Hold throttle lever closed or move carburetor control to IDLE or SLOW position and adjust idle adjusting needle until engine runs smoothly proceeding as in step six (6) above. 6 8. Allow several seconds between each adjustment when performing either step six (6) or seven (7) to allow engine to react to new setting. FIGURE 11. STORAGE INSTRUCTIONS In event engine is to be stored for any length of time (30 days or more), prepare as follows : 1. Drain gasoline by tipping or by syphon hose, then run engine until remainder is used and tank and carburetor are empty. ¿^CAUTION Drain into container outdoors away from fire or flame. 2. Drain carburetor by pressing upward on bowl drain (figure 11) 3. Inside protection of engine for storage is performed by removing spark plug and pouring one ounce of SAE 30 oil through spark plug hole into cylinder. Crank engine, without starting, several times to spread oii over cylinder walls. 7 I PARTS LIST FOR MODEL 247-650A REF. NO. PART NO. COLOR CODE DESCRIPTION NEW PART 1 11460 —463 Guide Extension Assembly 2 11472 —463 Guide Extension 3 736-0264 Flat Washer 5/16” Scr.* 4 712-0429 Elastic Stopnut 5/16-18 Thd. 5 11481 —463 Hopper Assembly 6 710-0621 Hex Scr. 5/16-18 x .50” Lg.* 7 736-0119 Spring L-Wash. 5/16” Scr.* 8 11479 —463 Clamp Rod Assembly 9 11454 —463 Back-up Plate 10 11467 —463 Inlet Guide Assembly 11 712-0429 Elastic Stopnut 5/16-18 Thd. 12 09966 Knob Ass’y. 13 736-0264 FI. Wash. .50” Dia.* 14 11480 Stop Washer 15 712-0429 Elastic Stopnut 5/16-18 Thd. 16 736-0264 FI. Wash. .50” Dia.* 17 711-0566 Chute Pivot Rod 18 712-0107 Hex Center L-Nut 1A-20 Thd. 19 710-0289 Hex Scr. 1/4-20 x .50” Lg.* *For faster service obtain standard nuts and bolts locally. If these items cannot be obtained locally, order by part number and size as shown on the parts list. (463—Top Flite Red) When ordering parts, if color or finish is important, use color code shown at left. (e.g. Top Flite Red Finish—11460 (463).) The engine is not under warranty by the mower manufacturer. If repairs or service is needed on the engine, please contact your nearest authorized engine service outlet. Check the “Yellow Pages” of your telephone book under “Engines — Gasoline.” Find It Fast In The Yellow Pages 9 I 247-650A keep this door closed except when feeding material CAUTION REVOLVING BLADE keep hands away from all openings 10 PARTS LIST FOR MODEL NO. 247-650A REF. NO. PART NO. COLOR CODE DESCRIPTION NEW PART 1 11476 —463 Door—Upper Guide Ext. 2 710-0465 Hex Scr. V2-20 x 4.50” Lg.* 3 711-0580 Clevis Pin 4 711-0579 Flail Spacer 7/32” Lg. 5 11455 —463 Cutting Finger Lockwasher Vz" Scr.* 6 736-0921 7 726-0111 Palnut 3/16” Dia. 8 712-0922 Hex Jam Nut 1/2-20 Thd.* 9 714-0507 Cotter Pin 3/32” Dia. x W' 10 11465 —463 Lg.* Chute Deflector 11 712-0107 L-Nut V4-20 Thd. 12 710-0289 Hex Scr. 1/4-20 x .50” Lg.* 13 714-0114 Sq. Key 1/4” x 2.00” Lg.* 14 11473 —463 Impeller Assembly 15 710-0157 Hex Scr. 5/16-24 x %” Lg.* 16 736-0119 L-WaSh. 5/16” Scr.* 17 11452 —463 Hopper to Engine Mtg. Plate 18 19 11464 —463 Engine Engine Mounting Plate 20 712-0123 Hex Nut 5/16-24 Thd.* 21 736-0119 L-Wash. 5/16” Scr.* 22 736-0119 L-Wash. 5/16” Scr.* 23 712-0123 Hex Nut 5/16-24 Thd.* 24 726-0221 Push Cap 25 26 07006 08306 —522 Fortiflex Bearing Wheel Ass’y.—Comp. 27 736-0100 F. Wash. .50” I.D.* 28 710-0624 Hex Scr. 5/16-24 x 1.50” Lg.* 29 712-0429 Elastic Stopnut 5/16-18 Thd. 30 710-0237 Hex Scr. 5/16-24 x .62” Lg.* 31 714-0144 Cotter Pin 1/8” Dia. x 1.00” 32 736-0192 Lg.* FI. Wash. .531 ” I.D. x .937 33 11459 —463 O.D. x .09 Flail 34 711-0564 Flail Spacer 23/32” Lg. 35 711-0578 Clevis Pin .50” Dia. x 3.0” Lg. 36 736-0247 FI. Wash. .406” I.D. x 1.25” 37 736-0217 O.D. Hdn. L-Wash. 3/8” Scr. Heavy Duty 38 710-0151 Hex Scr. 3/8-24 x 2.00” Lg. 39 11474 —463 H.T. Flail Housing Ass’y.—-Comp. 40 712-0107 Hex Center L-Nut Vi-20 Thd. 41 11477 —463 Upper Guide Extension Ass’y. 42 43 11478 726-0111 Hinge Pin Palnut 3/16” Dia. 44 712-0109 Wing Nut Elastic 1/4-20 Thd. 45 11458 —463 Blade 46 11475 —463 Axle 47 764-0126 Bag (Not Shown) 48 12968 —463 Blade Retainer a/x, A N •For faster service obtain standard nuts, bolts and washers locally. If these Items cannot be obtained ...
Эта инструкция также подходит к моделям:Измельчители садовые - 247-650-300 (1.44 mb)