Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
4. Lift up and remove the motherboard. 5. Screw in the brass standoffs to the threaded holes that line up with the motherboard. 6. Place the motherboard on the brass standoffs. Screw in the motherboard to the standoffs with the provided Phillips-head screws. 3 2.4 Flexi-Drive Bay System The Nine Hundred Two comes with nine 5.25” external drive bays at the front of the case. There are two HDD cages pre-installed inside the bottom six 5.25” bays. Each HDD cage occupies three consecutive 5.25” drive bays and can house three hard disk drives. For maximum flexibility you can mount the HDD cage anywhere within the external drive bays (i.e., you are not limited to the bottom six bays). Possible drive bay combinations include but are not limited to: • External 3 x 5.25” + internal 6 x HDD • External 6 x 5.25” + internal 3 x HDD • External 9 x 5.25” There is a middle fan bracket pre-installed on one of the HDD cages. You can install a 120mm fan to the bracket so the air will be blown into the case to use the HDD cage as a cooling duct to cool your graphics card or CPU. This will prevent the installation of hard drives into this cage, however. Remove the middle fan bracket from the HDD cage if you decide to mount your hard drives into this cage. • External 3 x 5.25” + internal 3 x HDD + cooling duct 2.5 Internal 3.5” Device Installation 1. Remove both side panels per the instructions in Setting Up. 2. Remove the cage thumbscrews fastening the HDD cage to the frame. 3. Slide the HDD cage forward out of the front of the case. 4. Mount the hard drive in the drive cage and fasten it using the long screws provided. 5. Slide the HDD cage back into the case and fasten it with thumbscrews. 4 6. Connect the appropriate connector(s) from the power supply to the device(s). Leave some slack in the connections so that you can easily access the fan filters for cleaning. 7. There is a 120mm fan pre-installed onto each cage. Connect the 4-pin connector to the power supply. Note: There is a middle fan bracket pre-installed on one of the HDD cages. Remove it from the cage if you decide to mount your hard drives into this cage. 2.6 External 3.5” Device Installation 1. Remove both side panels per the instructions in Setting Up. 2. Remove the drive bay cover from the drive bay you wish to install an external 3.5” drive into. 3. Install your external 3.5” device into the adapter. 4. Slide the drive adapter/device assembly into the bay. 5. Screw the adapter to the drive cage. 6. Mount the faceplate and secure it with screws. 2.7 External 5.25” Device Installation Note: The HDD cages each occupy three consecutive drive bays, and will block installation of larger devices such as optical drives, so please plan ahead before installing your drives. 1. Remove both side panels per the instructions in Setting Up. 2. Remove the screws fastening the appropriate metal drive bay cover(s) to the sides of the case. 3. Remove the cover(s). 4. If necessary, please remove the HDD cage that is pre- installed in the bay. 5. Slide the 5.25” device into the bay from the front of the case. 6. Fasten the drive using the screws that came with your drive. 7. Connect the appropriate power and interface connectors from the power supply and motherboard to the device. Make sure that you leave some slack in the connections so that you can easily access the fan filters for cleaning. 8. Mount the other devices accordingly. 5 2.8 Cable Management Compartment There is a cable management compartment between the motherboard and right side panel. You can tuck or route excess cables in this compartment. 1. Remove both side panels. 2. Choose the cables you would like to pass through the holes behind the motherboard tray and pull them out of the power supply chamber towards the right side of the case. 3. Use the cable ties provided to hold them in place. 4. Feed the cables back through the insertion point nearest the destination of the cable. Connect the cable and then pull the slack back to the right side of the case. 2.9 Water Cooling Platform This case comes with a 5.25” metal plate pre-installed in the 3rd 5.25” drive bay. This plate is designed to allow you to easily mount components of a water-cooling kit such as a pump or reservoir. The plate can be mounted in any of the nine 5.25” drive bays for maximum flexibility. Note: The plate is not pre-drilled. You will need to drill the appropriate holes to be compatible with your water-cooling kit. 2.10 Three-Way NVIDIA™ SLI™ Configuration Option The Nine Hundred Two has eight expansion slots, making it capable of supporting up to three graphics cards in triple- NVIDIA™ SLI™ configuration. Consult your motherboard and graphics cards manuals for more information. Connecting the Front I/O Ports 3.1 USB 2.0 Connect the front I/O panel USB cable to the USB header pin on your motherboard. Check the motherboard manual to ensure that it matches the table below: Motherboard USB Pin Layout 1 2 Pin Signal Names Pin Signal Names 1 USB Powe...