Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
• Take care not to hold one of the buttons on the Hand Controller until the Lifting Strap switches direction. The UP button should always pull the strap up and vice versa. If your buttons cause opposite movement, contact your distributor. Loading your Scooter or Power Chair —Enclosed Vehicle Applications Note: Due to the wide variety of scooters, power chairs and vehicles, your dealer may offer a different method for Loading and Unloading your scooter. Please follow the guidelines they have offered. • Unhook the Strap Hook or optional C-Arm from the gusset on the Base (recommended stowed position). • Swing the Lifting Arm out of the vehicle toward the scooter. • Maneuver the scooter parallel to the rear bumper and two inches behind the vehicle. Depending on the vehicle, it may be necessary to: remove the seat; fold down or remove the handle bar; remove accessories such as brackets, baskets, crutch holders, etc. Note: When using the Offset Post Conversion, position the scooter on the side of the vehicle parallel to the vehicle with the front tires even with the vehicle’s rear bumper. • With the docking device positioned directly under the Strap Hook, lower the Lifting Strap using the DOWN button on the Hand Control until the Strap Hook (or C-Arm) can be engaged into the docking device installed on the scooter or chair. Hook the docking device on the scooter or chair with the Strap Hook and remove any play in the strap by pushing the UP button on the Hand Control until tension is felt. Caution: Ensure that the Lifting Strap is secure and taught and that it points straight down. Failure to do so could result in the scooter or chair swinging toward the operator of the vehicle. • Raise the scooter or chair using the UP button until the scooter or chair is just above the highest obstacle. This is usually the van floor, door sill or tailgate. Caution: Stop lifting before the Strap Hook contacts the Strap Roller mounted on the Lifting Arm. Contact will result in damage to the lift. A properly adjusted and operated lift will avoid this. • Swing the scooter or chair into the vehicle, ensuring that the scooter or chair does not contact the vehicle. • With the scooter or chair positioned above its stowed position, lower the lift using the DOWN button on the Hand Controller. The scooter or chair should be lowered until it is sitting firmly on the floor but the strap should remain taut. This facilitates a quicker and easier unloading of the scooter later. Caution: Ensure that the scooter or chair is firmly sitting on the floor and not suspended by the lift If preparations need to be made to secure the scooter or power chair for transport, such as parking brakes or wheel chocks, do these now. Dealers should instruct operators on how, if necessary to secure the scooter or chair for transport. Place the Hand Control on the Velcro mounting pad and close the doors or tailgate and you are ready to go. 9 Section 4 -Operating the AL200 Lift continued Enclosed Vehicle Applications Unloading Your Scooter or Power Chair —Enclosed Vehicle Applications • Undo any preparations made to secure the scooter or power chair for transport. • Raise the scooter or chair by pressing the UP button on the Hand Control until the tires are high enough to clear the highest obstacle, usually the door sill or tailgate. Caution: Stop lifting before the Strap Hook contacts the Strap Roller mounted on the Lifting Arm. Contact will result in damage to the lift. A properly adjusted and operated lift will avoid this. • Swing the scooter or chair out of the vehicle, carefully ensuring that the scooter does not contact the vehicle. • With the scooter or chair positioned away from the vehicle, lower the lift using the DOWN button. Continue lowering the lift slightly beyond the scooter or chair touching the ground to allow removal of the Strap Hook from the docking device on the scooter. Caution: Do not allow the scooter or chair to come in contact with the vehicle. Damage may result to both the vehicle AND the operator. Replace anything removed from the scooter or chair for loading purposes. Swing the Lifting Arm back into the vehicle and place the Hand Control on the Velcro mounting pad. Close the doors or tailgate and you are ready to go. PLEASE PROCEED TO SECTION #7 FOR SAFETY AND MAINTENANCE INFORMATION. 10 11 Section 5 - Installing the AL400 Fully Powered Lift • You should have established a mounting position for the lift during the “trial fit” as described in Section #2 of this manual. If not, it is recommended that you go through that procedure. Note: The Base should be mounted as far to the rear corner of the vehicle as possible in most rear mount applications. • Mount the lift in the location determined during the “trial fit” in the vehicle. The Leg Extensions in the Base telescope in and out to avoid potential obstacles. For heavy applications, pull the Leg Extensions out as far as is practical for increased base stability. Mark the 3 mounting hole l...
Эта инструкция также подходит к моделям:Инвалидные коляски - AL055 (410.6 kb)
Инвалидные коляски - AL400 (410.6 kb)