Оценок - 2, средний балл: 4 ( )

Производитель: Razor Размер: 1.67 mb Название файла: Язык инструкции:

Use ONLY with the recommended charger. q Replacement Parts The most frequently requested replacement parts (wheels, tires, tubes, batteries and chargers) are available for purchase at some Razor retail partners or online at For other parts contact an authorized Razor repair center. q Repair Centers For a list of authorized Razor repair centers: • Check online at • Send e-mail to customerservice@razorusa.com or call 866-467-2967 for the center nearest you. and place the damaged battery in a plastic bag. Refer to the disposal instructions at left. If acid comes into contact with skin or eyes, flush with cool water for at least 15 minutes and contact a physician. 10 TROUBLESHOOTING GUIDE Problem Possible Cause Solution Scooter does not run Undercharged battery Charger is not working Loose wires or connectors E100 only - Scooter must be traveling 3mph before motor will engage. Charge the battery. A new battery should have been charged for at least 12 hours before using the scooter for the first time and up to 8 hours after each subsequent use. Check all connectors. Make sure the charger connector is tightly plugged into the charging port, and that the charger is plugged into the wall. Make sure power flow to the wall outlet is on. You may check to see if your charger is working by using a volt meter or asking your local Razor authorized service center to test your charger for you. Kick start to 3mph then twist the throttle to start motor. Scooter was running but suddenly stopped Tripped circuit breaker Check all wires and connectors to make sure they are tight. The circuit breaker (next to on/off switch) will automatically shut off the power if the motor is overloaded. An excessive overload, such as too heavy a rider or too steep a hill, could cause the motor to overheat. If the scooter suddenly stops running, wait a few seconds and then push the breaker to reset the circuit. Correct the conditions that caused the breaker to trip and avoid repeatedly tripping the breaker. Short run time (less than 30 minutes per charge) Undercharged battery Charge the battery. A new battery should have been charged for at least 12 hours before using the scooter for the first time and up to 8 hours after each subsequent use. Check all wires and connectors. Make sure the battery connector is tightly plugged into the charger connector, and that the charger is plugged into the wall. Battery is old and will not accept full charge Make sure power flow to the wall outlet is on. Even with proper care, a rechargeable battery does not last forever. Average battery life is 1 to 2 years depending on scooter use and conditions. Replace only with a Razor replacement battery. Brakes are not adjusted properly Refer to adjusting the brakes instructions on page 4. Scooter runs sluggishly Driving conditions are too stressful Use only on solid, flat, clean and dry surfaces such as pavement or level ground. Tires are not properly inflated The tires are inflated when shipped, but they invariably will lose some pressure between the point of manufacturing and your purchase. Refer to instructions on page 5 of this manual to properly inflate tires. Scooter is overloaded Make sure you do not overload the scooter by allowing more than one rider at a time, exceeding the E100 120 lb. or E200 and E300 220 lb. maximum weight limit, going up a hill or towing objects behind the scooter. If the scooter is overloaded, the circuit breaker may trip and shut off power to the motor. Correct the driving conditions that caused the overload, wait a few seconds, and then push the breaker to reset the circuit. Avoid repeatedly tripping the circuit breaker. Brake dragging E100: Use your fingers to twist the adjuster in either direction until wheel is centered between pads. E200/E300: Adjust brake at lever (page 4) to allow wheel to spin without brake contact. 11 TROUBLESHOOTING GUIDE Problem Possible Cause Solution Sometimes the scooter doesn’t run, but other times it does Brakes are not adjusted properly Loose wires or connectors Refer to adjusting the brakes instructions on page 4. Check all wires around the motors and all connectors to make sure they are tight. Charger gets warm during use Motor or electrical switch damage Contact your local Razor authorized service center for diagnosis and repair. Scooter does not stop when applying the brake Normal response to charger use No action required. This is normal for some chargers and is no cause for concern. If your charger does not get warm during use, it does not mean that it is not working properly. Scooter makes loud noises or grinding sounds Brakes are not adjusted properly Chain is too dry Refer to adjusting the brakes instructions on page 4. Apply a lubricant such as 3 in 1TM or Tri-FlowTM to the chain. Brake rotor is dragging on brake pads Use your fingers to twist the caliper adjuster in either direction until rotor is centered between pads. N NNe eee eed ddH HHe eel llp pp? ??V VVi...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: